Geometric Dimensioning and Tolerancing for Mechanical Design Part 6 ppt
Geometric Dimensioning and Tolerancing for Mechanical Design Part 6 ppt
... (www.digitalengineeringlibrary.com) Copyright © 20 06 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design ... 1° 2.00 3.00 Figure 6- 16 Specifying perpendicularity of a surface. 20. Supply the appropriate geometric tolerance on the drawing in Fig...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 6 ppt
... (www.digitalengineeringlibrary.com) Copyright © 20 06 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: ... used of the 14 geometric characteristics. The position tolerance significantly contributes to part function, part interchangeabilit...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 5 pptx
... the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-04 MHBD031-Cogorno-v6.cls April 10, 20 06 20:8 1.500 w 1.000- 1.030 4X . 760 790 2.500 1.500 3.000 3.500 ... 1.020 apart, and the entire cylindrical part must fit inside a cylindrical hole 1.020 in diameter. Just as for flatness, if the thickness/diameter of the parts is prod...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 7 ppt
... (www.digitalengineeringlibrary.com) Copyright © 20 06 The McGraw-Hill Companies. All rights reserved. Any use is subject to the Terms of Use as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: ... actual feature size and its MMC. Bonus tolerance for a particular feature is added directly to the geometric tolerance to equal th...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 8 ppt
... available. A drill chart and a chart of oversize diameters in drilling are located in the appendix of this text. TABLE 8-1 Drill Chart Letter Fraction Decimal 17 /64 . 266 H – . 266 I – .272 J – .277 9/32 ... datums B and C depart from MMC. The pattern-locating tolerance zone framework is parallel to and located from datumplane A, perpendicular to datum axis B, and clocked to datum...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 12 pptx
... MHBD031-Cogorno-v6.cls April 11, 20 06 21:50 Chapter 14 A Strategy for Tolerancing Parts When tolerancing a part, the designer must determine the attributes of each feature or pattern of features and the ... a part. Some designers believe that parts designed with a solid modeling CAD program do not require tolerancing. A note in the Dimen- sioning and Tolerancing standard indi...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 doc
... website. Introduction to Geometric Dimensioning and Tolerancing P1: PBU introduction1 MHBD031-Cogorno-v6.cls April 8, 20 06 17:58 Chapter 1 Introduction to Geometric Dimensioning and Tolerancing For many in ... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geom...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 1 pps
... MHBD031-Cogorno-v6.cls April 8, 20 06 17:58 Chapter 1 Introduction to Geometric Dimensioning and Tolerancing For many in the manufacturing sector, geometric dimensioning and tolerancing (GD&T) ... website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design Contents Preface ix Acknowledgments xi Chapter 1. Introduction to Geometric Dim...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 potx
... given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 20 06 18 :6 Dimensioning and Tolerancing Fundamentals 11 44.72° 25° ... given at the website. Introduction to Geometric Dimensioning and Tolerancing P1: PBU MHBD031-02 MHBD031-Cogorno-v6.cls April 8, 20 06 18 :6 Dimens...
Ngày tải lên: 05/08/2014, 09:20
Geometric Dimensioning and Tolerancing for Mechanical Design Part 2 pps
... as given at the website. Source: Geometric Dimensioning and Tolerancing for Mechanical Design P1: PBU MHBD031-03 MHBD031-Cogorno-v6.cls April 18, 20 06 15:58 26 Chapter Three Between Symbol X Z Tolerance ... 20 06 18 :6 Chapter 2 Dimensioning and Tolerancing Fundamentals Many people know how to design parts and make drawings, yet they lack the basic knowledge to...
Ngày tải lên: 05/08/2014, 09:20