Gear Noise and Vibration Episode 2 Part 1 docx

... cutting process (Part 1) . Trans. ASME J. Eng. Ind. 10 0, 22 2 22 8. Usui, E. and Hirota, A. (19 78) Analytical prediction of three dimensional cutting process (Part 2) . Trans. ASME J. Eng. Ind. 10 0, 22 9 23 5. Usui, ... 19 5 Fig. 6 .18 The dependence of η c on (a) λ s and (b) r n , for machining a carbon steel (after Usui and Hirota, 19 78) (a) Childs Part 2 28:3 :20...

Ngày tải lên: 21/07/2014, 17:20

... adjacency matrix of the spur -gear set shown in Figure 3 .2 is given by A =     011 1 10 10 11 01 1 010     . (3 .2) The matrix representation given by Equation (3 .2) provides no distinction for ... outlined below. joint j B =      b 1, 1 b 1 ,2 ··· b 1, m b 2, 1 b 2, 2 ··· b 2, m . . . . . . . . . . . . b n ,1 b n ,2 ··· b n,m      link i where b ij = ...

Ngày tải lên: 21/07/2014, 17:20

... y0 w0 h1" alt=""

Ngày tải lên: 21/07/2014, 17:20

... TEST 2 Answer Key Math Level IC 1. C 2. A 3. E 4. A 5. D 6. E 7. B 8. D 9. D 10 . C 11 . E 12 . B 13 . C 14 . E 15 . C 16 . D 17 . D 18 . C 19 . C 20 . B 21 . A 22 . D 23 . C 24 . C 25 . A 26 . C 27 . E 28 . D 29 . ... 8 42 (C) 20 02 (D) 25 22 (E) 51 02 42. (A) 48 (B) 54 (C) 11 52 (D) 12 8 (E) 72 43. In a class of 25 0 students, 17 5 take mathematics an...

Ngày tải lên: 22/07/2014, 10:22

... paragraph 3.3 .11 in ASME Y14.5M -19 94. 6 .2. 3 .2 ISO The ISO standards referenced in Tables 6-6 through 6 -13 are: ISO 11 01- 1983 ISO 8 015 -19 85 ISO 10 578 -19 92 ISO 16 60 -19 87 ISO 5458 -19 87 ISO 10 579 -19 93 ISO 26 92- 19 88 ... ISO 26 92- 19 88 ISO 5460 -19 85 ISO 12 9 -19 85 ISO 27 68 -19 89 ISO 5459 -19 81 The numbers in the parentheses represent the standard and...

Ngày tải lên: 21/07/2014, 15:20

Ngày tải lên: 13/12/2013, 03:15

Ngày tải lên: 13/12/2013, 03:15

... gears 19 3 11 .6 Modelling rattle 19 4 Reference 20 0 12 . Planetary and Split Drives 20 1 12 . 1 Design philosophies 20 1 12 . 2 Advantages and disadvantages 20 3 12 . 3 Excitation phasing 20 5 12 . 4 ... 18 1 References 18 3 11 . Lightly Loaded Gears 18 5 11 .1 Measurement problems 18 5 11 .2 Effects and identification 18 7 11 .3 Simple...

Ngày tải lên: 03/07/2014, 12:20

... Vol 1 72, 19 58, pp 87 -1 12 . 4. Gregory, R.W., Harris, S.L. and Munro, R.G., 'Dynamic behaviour of spur gears.' Proc. Inst. Mech. Eng., Vol 17 8, 19 63-64, Part I, pp 20 7 -22 6. 5. ... attainable. References 1. Gregory, R.W., Harris, S.L. and Munro, R.G., 'Dynamic behaviour of spur gears.' Proc. Inst. Mech. Eng., Vol 1...

Ngày tải lên: 03/07/2014, 12:20

... Biometrika 52( 3 and 4):547-558. 9. Ramberg, J.S., P.R. Tadikamalla, E.J. Dudewicz, E.F. Mykytha. 19 79. A Probability Distribution and Its Uses in Fitting Data. Technometrics. 21 (2) :20 1 - 21 4. 10 . Stoddard, ... Information 1 2 4 3 5 6 7 16 - 12 Chapter Sixteen 16 .4 .2. 1 Workspace The workspace is the area where the daily development efforts take place. This is where...

Ngày tải lên: 21/07/2014, 15:20