Gear Noise and Vibration Episode 1 Part 1 potx
Metal Machining - Theory and Applications Episode 2 Part 1 potx
... Usui and Hirota, 19 78) (a) Childs Part 2 28:3:2000 3 :13 pm Page 19 5 19 93; Ceretti et al., 19 96) and elastic–plastic (Marusich and Ortiz, 19 95) adaptive remesh- ing softwares have been developed and ... experiment as (with angles in rad and t sh in MPa) f = exp(0.581a – 1. 139) t sh = 517 .4 – 19 .89a } (6.52) l = exp(0.848a – 0. 416 ) Figure 6 .18 compares the measur...
Ngày tải lên: 21/07/2014, 17:20
Gear Noise and Vibration P1 potx
... 18 1 References 18 3 11 . Lightly Loaded Gears 18 5 11 .1 Measurement problems 18 5 11 .2 Effects and identification 18 7 11 .3 Simple predictions 18 9 11 .4 Possible changes 19 2 11 .5 Anti-backlash gears ... 10 6 7.8 Accuracy of measurement 11 0 7.9 Worms and wheels and spiral bevels 11 2 7 .10 Practical problems 11 3 7 .11 Comparisons 11...
Ngày tải lên: 03/07/2014, 12:20
Gear Noise and Vibration P2 ppsx
... Thompson, A.M. Dynamics and noise of parallel axis gearing. Inst. Mech. Eng. Conf. Gearing in 19 70, Sept, pp 11 1 -12 1. 8. Furley, A.J.D., Jeffries, J.A. and Smith, J.D., 'Drive ... Mech. Eng., Vol 17 2, 19 58, pp 87 -11 2. 4. Gregory, R.W., Harris, S.L. and Munro, R.G., 'Dynamic behaviour of spur gears.' Proc. Inst. Mech. Eng., Vol...
Ngày tải lên: 03/07/2014, 12:20
Dimensioning and Tolerancing Handbook Episode 3 Part 1 ppt
... flow solid Part1 facet normal 0.000000e+000 0.000000e+000 1. 000000e+000 outer loop vertex 1. 875540e-0 01 2. 619 040e-0 01 4 .14 6040e-0 01 vertex 1. 875540e-0 01 2. 319 040e-0 01 4 .14 6040e-0 01 vertex 2 .17 5540e-0 01 ... BASIC ACTUAL 1 . 312 ±.003 .309 . 311 .002 Ø. 012 1. 500 1. 503 +.003 2 .500 2 .5 01 +.0 01 2 . 312 ±.003 .309 ....
Ngày tải lên: 21/07/2014, 15:20
Dimensioning and Tolerancing Handbook Episode 2 Part 1 pptx
... paragraph 3.3 .11 in ASME Y14.5M -19 94. 6.2.3.2 ISO The ISO standards referenced in Tables 6-6 through 6 -13 are: ISO 11 01- 1983 ISO 8 015 -19 85 ISO 10 578 -19 92 ISO 16 60 -19 87 ISO 5458 -19 87 ISO 10 579 -19 93 ISO ... ISO 2692 -19 88 ISO 5460 -19 85 ISO 12 9 -19 85 ISO 2768 -19 89 ISO 5459 -19 81 The numbers in the parentheses represent the standard and paragraph number. For ex...
Ngày tải lên: 21/07/2014, 15:20
Dimensioning and Tolerancing Handbook Episode 1 Part 4 potx
... METRIC Code Size Code Size A 8.5 X 11 A4 210 X 297 B 11 X 17 A3 297 X 420 C 17 X 22 A2 420 X 594 D 22 X 34 A1 594 X 8 41 E 34 X 44 A0 8 41 X 11 89 4.6 Title Blocks The part of a drawing that has the ... section Figure 4 -14 Half section Drawing Interpretation 4- 21 Figure 4 -15 Offset section Figure 4 -16 Broken-out section Geometric Dimensioning and Tolerancing 5-3 • ASME Y14.5M...
Ngày tải lên: 21/07/2014, 15:20
Dimensioning and Tolerancing Handbook Episode 1 Part 1 pdf
... Performance, P 6 11 -15 11 .5.4 Is P≥P 6 ? 11 -16 11 .5.5 Allocating Tolerances 11 -17 11 .5.6 Statistical Allocation Summary 11 -20 11 .6 Dynamic RSS Allocation 11 -20 11 .7 Static RSS analysis 11 -23 11 .8 Comparison ... 11 -8 11 .4.4 Calculate the Worst Case Assembly, t wc6 11 -8 11 .4.5 Is P≥t wc6 ? 11 -9 11 .4.6 Estimating Defect Rates 11 -10 11 .4.7 Verification 1...
Ngày tải lên: 21/07/2014, 15:20
Metal Machining - Theory and Applications Episode 1 Part 5 potx
... per unit feed and also cutting speed. Work material characteristics in machining 91 Fig. 3 .11 Process stresses and temperatures derived from (and symbols as) Figure 3 .10 Childs Part 1 28:3:2000 ... Mech. 18 , 405– 413 . Mallock, A. (18 81 82) The action of cutting tools. Proc. Roy. Soc. Lond. 33, 12 7 13 9. Merchant, M. E. (19 45) Mechanics of the metal cutting process. J. Appl...
Ngày tải lên: 21/07/2014, 17:20