Friction and Lubrication in Mechanical Design Episode 1 Part 9 potx

Ngày tải lên: 13/12/2013, 03:15

... This page intentionally left blank

Ngày tải lên: 13/12/2013, 03:15

... References 57 62 76 90 97 10 0 10 0 10 0 10 5 11 1 11 3 11 3 11 4 11 5 11 6 11 8 12 1 12 1 12 1 12 3 12 7 13 5 14 2 15 8 16 1 16 1 18 7 2 09 230 246 6 Chapter I of the static and oscillatory ... 10 1. 10 2. 10 3. 10 4. 10 5. 10 6. 10 7. 10 8. 10 9. 11 0. 11 1. 11 2. 11 3. Numerical Methods for Engineen'ng Applications, Edward R. Cha...

Ngày tải lên: 04/07/2014, 14:20

... Rolling and Sliding of Bodies,” Wear, 19 68, Vol. 11 , p. 2 91 . Kelley, B. W., and Lemaski, A.J., Lubrication of Involute Gearing,” Proc. Inst. Mech. Engrs, 19 67-68, Vol. 18 2, Pt. 3A, p. 17 3. ... Disk in Pure Sliding, New Type of Oil Film Formation,” J Inst. Petrol., Vol. 37, p. 4 71. 15 , 19 66, pp. 41- 50. pp. 14 9 -15 9. Introduction 13 later introduced...

Ngày tải lên: 04/07/2014, 14:20

... g-sec, ft/s in/ s cm/s m/s or Æ g ft/s 2 in/ s 2 cm/s 2 m/s 2 By To obtain value in Ø g-s, 1 0.0 311 0.002 59 0.0 010 2 0 .10 2 g ft/s 32 .16 1 0.0833 0.0328 3.28 ft/s 2 in/ s 386 12 .0 1 0. 393 7 39. 37 in/ s 2 cm/s ... rad/s 2 degree/s 2 rev/s 2 rev/min/s By To obtain value in Ø rad/s 1 0. 017 45 6.283 0 .10 47 rad/s 2 degree/s 57.30 1 360 6.00 degree/s 2 rev/s 0 .15...

Ngày tải lên: 21/07/2014, 16:22

... B. Hansen ,and P. K. Wright. 19 89. Self-sustaining, open-system machine tools. In Proceedings of the i7th North American Manufacturing Research institution 17 :2 81- 292 . Groover, M. P. 19 99 . Fundamentals ... 19 96 ;DeMeter et al., 19 95 ;Mitsuishi et al., 19 92 ;Frost and Cutkosky , 19 96 ;Finin et al. , 19 94 ) .In summary: •SLA emerges as the most commercially accept...

Ngày tải lên: 21/07/2014, 17:20

... (c) influx (d) plug 297 Answers Index PHOTOCOPIABLE © www.english-test.net Test 296 TOEIC Vocabulary / Word by Meaning / Test # 296 Q1 n. act of bringing back; restoration; act of finding information ... Word by Meaning / Test # 283 Q1 n. business of supplying and servicing food (a) safety (b) equipment (c) minimum (d) catering Q2 n. person who participates in a bargaining session (a)...

Ngày tải lên: 21/07/2014, 22:20

... B 8. B 9. C 10 . D 11 . D 12 . B 13 . E 14 . A 15 . C 16 . B 17 . C 18 . B 19 . D 20. B 21. B 22. C 23. E 24. D 25. E 26. D 27. C 28. A 29. E 30. B 31. D 32. E 33. C 34. C 35. D 36. B 37. B 38. E 39. D 40. ... 8 in. The length of the tangent from the point to the circle is (A) (B) 15 (C) 9 (D) (E) 17 . In the formula , if C = 3 × 10 10 and L = 6 × 10 –5 , f = (...

Ngày tải lên: 22/07/2014, 10:22

... 10 –2 (10 1 ) n < 10 –2 1 10 ⎛ ⎝ ⎜ ⎞ ⎠ ⎟ n < 10 –2 1 10 ⎛ ⎝ ⎜ ⎞ ⎠ ⎟ n < 0. 01 SUFFICIENT. (2) 1 10 ⎛ ⎝ ⎜ ⎞ ⎠ ⎟ n − 1 < 0 .1 1 10 ⎛ ⎝ ⎜ ⎞ ⎠ ⎟ n − 1 < 10 1 (10 1 ) n ... 19 70 ? (1) The price of the Model K mixer was $10 2.40 more in 19 89 than in 19 70. (2) The price of the Model K mixer was $14 2.40 in 19 89. Arithmetic Propor...

Ngày tải lên: 22/07/2014, 14:20

... ¼ mUL 3 2C 2 ð p 0 e sin 2 y 1 þe cos yÞ 3 dy ð7 -12 bÞ The following list of integrals is useful for short journal bearings. J 11 ¼ ð p 0 sin 2 y 1 þ e cos yÞ 3 dy ¼ p 2 1 Àe 2 Þ 3=2 ð7 -13 aÞ J 12 ¼ ð p 0 sin ycos ... ¼ mn P R C  2 ¼ D L  2 1 Àe 2 Þ 2 pe½p 2 1 Àe 2 Þ 16 e 2  1= 2 From the right-hand side of the equation, S ¼ð2Þ 2 1 À 0:8 2 Þ 2 p0:8½p 2 1 À0:8 2 Þ 16 Â...

Ngày tải lên: 21/07/2014, 17:20