Dimensioning and Tolerancing Handbook Episode 3 Part 7 doc

... . 235 .0 57 .026 1 / 2 - 2 1 / 2 12800 5/16 .31 25 .31 27 .296 .006 . 071 5 . 032 5 1 / 2 - 2 1 / 2 20000 3/ 8 . 37 50 . 37 52 ±.0001 .35 8 .086 . 039 1 / 2 - 3 2 870 0 7/ 16 . 4 37 5 . 4 37 7 .4 17 .1005 .0455 7 / 8 ... .06 27 .0 53 .014 .006 3 / 16 – 3 / 4 800 3/ 32 .0 938 .094 .084 .0215 .0095 3 / 16 - 1 1800 1/8 .1250 .1252 .115 .005 .0285 .0125 3 / 8 - 2 32...

Ngày tải lên: 05/08/2014, 09:19

... .31 2 ±.0 03 .30 9 .31 0 .001 Ø.011 1.500 1.506 2.500 2.5 03 +.0 03 2 .31 2 ±.0 03 .30 9 .31 5 .006 Ø.016 1.500 1.505 1.000 1.006 +.006 3 .31 2 ±.0 03 ... 1.000 1.006 +.006 3 .31 2 ±.0 03 .30 9 .31 3 .004 Ø.014 4.500 4.506 2.500 2.499 - .001 4 .31 2 ±.0 03 .30 9 .31 2 .0 03 Ø.0 13 4.5...

Ngày tải lên: 21/07/2014, 15:20

... Establishing datum reference frames from part features Geometric Dimensioning and Tolerancing 5 -77 5.9.8.4 Fixed-size TGC According to Table 5-4, for features of size and bounded features referenced as ... interpret all dimen- sions and tolerances, including the circularity tolerance, as applying in the free state. The standard Geometric Dimensioning and Tolerancing 5 -71...

Ngày tải lên: 21/07/2014, 15:20

... assemblies. ASME Y14.5M-1994 (the Dimensioning and Tolerancing standard) and the ASME Y14.5.1M-1994 (the standard on Mathematical Principles of Dimensioning and Tolerancing) both state that occasionally ... interna- tional, and industrial standards research and development efforts in the areas of global tolerancing of mechanical parts and supporting metrology. Dr. Hetlan...

Ngày tải lên: 21/07/2014, 14:26

... .31 2±.0 03 .30 9 .31 1 .002 Ø.012 1.500 1.5 03 +.0 03 2 .500 2 .501 +.001 2 .31 2±.0 03 .30 9 .31 3 .004 Ø.014 1.500 1.505 1 .000 .998 - .002 3 .31 2±.0 03 ... / (dpo)^2)))^2 + 0.00 130 8 * (SQRT(LN(1 / dpo)^2))) ^3) +1.5 dpo = [(((((((1 + 0.04986 73 4 7 * (z –1.5)) + 0.0211410061 * (z –1.5) ^2) + 0.0 032 77 62 63 *(z -1.5)...

Ngày tải lên: 21/07/2014, 15:20

... ) 879 6.2 9162. 9162.125.540 07. 000.1625.2625. 170 0.1 875 .7 cos cossin 2 3 2 3 −= −−−−− = −−−−− = ∂ ∂ β ββ β Ψ KMEBCF ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) ( ) 133 1. 8805.125.1 474 1.625.1 875 . 8805. 474 1.125. 170 0.1 625 .3 474 1.125.18805.625.1 875 . 8805. 474 1.125. 170 0.1 625 .36 25.2 8805.125.1 474 1.625.1 875 . 8805. 474 1.125. 170 0.1 625 .3 cossin cos sin sincos cos sin c...

Ngày tải lên: 21/07/2014, 15:20

... answered: 20 -34 Chapter Twenty Figure 20-15 25-mm cube test—single versus star probe setup 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Parallelism = 1-2, Angularity = 3- 6, Width = 7- 10, ... of relationship between settling time and machine performance. 5 6 7 8 9 10 6 sigma Sphere Form (10^ -3 mm) 1.5 mm Probe 3. 0 mm Probe 0 1 2 3 4 0 0.5 1 1.5 2 2.5 3 3....

Ngày tải lên: 05/08/2014, 09:17

... .12 73 .12 73 .12 73 .12 73 T 1 .0010 .0010 .0010 .00 07 .00 07 .00 07 T 2 .0010 .0010 .0010 .00 07 .00 07 .00 07 µd .12 73 .12 73 .12 73 .12 73 .12 73 .12 73 σ d .00025 .00025 .00025 .00025 .00025 .00025 Distribution type Lognor mal Lognor mal Lognor mal Lognor mal Lognor mal Lognor mal Orientation 2Q ... Case 2 Case 3 Case 4 Case 5 Case 6 Feature Type Internal Internal I...

Ngày tải lên: 05/08/2014, 09:19

... -18 UNC .34 38 (11 /32 ) +.005/ 002 . 938 (15/16) +/ 010 .640 +/ 010 .31 2-24 UNF . 37 5-16 UNC .4062 ( 13/ 21) +.005/ 002 1.0 63 (1 1/16) +/ 010 .76 5 +/ 010 . 37 5-24 UNF . 438 -14 UNC .4688 (15 /32 ) +.005/ ... (9 /32 ) +.005/ 002 .510 +/ 010 .250-28 UNF .31 2 -18 UNC .34 38 (11 /32 ) +.005/ 002 .640 +/ 010 .31 2-24 UNF . 37 5-16 UNC .4062 ( 13/ 21) +.005/ 002 .76 5 +/ 010 . 37 5-2...

Ngày tải lên: 05/08/2014, 09:19

... Missouri Author of the book, Design Dimensioning and Tolerancing Member and officer on national and international standards development committees The Future of Dimensioning and Tolerancing* Changes are ... each standard to industry as well as recommended paths for the phase-out of existing standards to be obsolete. The Future of Dimensioning & Tolerancing Standards D...

Ngày tải lên: 05/08/2014, 09:19