Dimensioning and Tolerancing Handbook Episode 3 Part 4 potx

... METRIC Code Size Code Size A 8.5 X 11 A4 210 X 297 B 11 X 17 A3 297 X 42 0 C 17 X 22 A2 42 0 X 5 94 D 22 X 34 A1 5 94 X 841 E 34 X 44 A0 841 X 1189 4. 6 Title Blocks The part of a drawing that has the highest ... Four Figure 4- 13 Full section Figure 4- 14 Half section Drawing Interpretation 4- 21 Figure 4- 15 Offset section Figure 4- 16 Broken-out section Geometric Dimensi...

Ngày tải lên: 21/07/2014, 15:20

... into assemblies. ASME Y 14. 5M-19 94 (the Dimensioning and Tolerancing standard) and the ASME Y 14. 5.1M-19 94 (the standard on Mathematical Principles of Dimensioning and Tolerancing) both state that ... interna- tional, and industrial standards research and development efforts in the areas of global tolerancing of mechanical parts and supporting metrology. Dr. Hetlan...

Ngày tải lên: 21/07/2014, 14:26

... 1.006 +.006 3 .31 2 ±.0 03 .30 9 .31 3 .0 04 Ø.0 14 4. 500 4. 506 2.500 2 .49 9 - .001 4 .31 2 ±.0 03 .30 9 .31 2 .0 03 Ø.0 13 4. 500 4. 501 1.000 1.005 +.005 X ... 1 .48 2±.002 .48 0 .48 2 .002 Ø.009 2.200 2.2 03 +.0 03 0 0 0 2 . 48 2±.002 .48 0 .4 83 .0 03 Ø.010 - .900 - .905 1 .31 8 1...

Ngày tải lên: 21/07/2014, 15:20

... - .002 3 .31 2±.0 03 .30 9 .31 2 .0 03 Ø.0 13 4 .500 .49 6 2 .500 2 .49 7 - .0 03 4 .31 2±.0 03 .30 9 .31 0 .001 Ø.011 4 .500 .49 4 1 .000 1.002 +.002 ... .31 2±.0 03 .30 9 .31 1 .002 Ø.012 1.500 1.5 03 +.0 03 2 .500 2 .501 +.001 2 .31 2±.0 03 .30 9 .31 3 .0 04 Ø.0 14 1.500 1....

Ngày tải lên: 21/07/2014, 15:20

... 1.79 84. (For example, .0 030 is resized to 1.79 84* .0 030 = .00 54. ) 0.0000 0.0100 0.0200 0. 030 0 0. 040 0 0.0500 0.0600 0. 035 4 0. 038 1 0. 040 9 0.0 43 7 0. 046 6 0. 049 5 0.0525 0.0555 0.0585 0.0615 0.0 646 Assembly ... Variable .0060 .00 24 .0060 .0108 .0060 .0079 .30 00 1.0000 Variable . 030 0 .0118 . 030 0 .0 540 . 030 0 . 039 6 Nominal Gap .0615 .0615 .0615 .0615 .0615 .0615...

Ngày tải lên: 21/07/2014, 15:20

... values are defined in ASME Y 14. 5.1M-19 94. (See Chapter 7 for details about the Y 14. 5.1M-19 94 standard that provides math- ematical definitions of dimensioning and tolerancing principles.) Some ... limit and a lower limit. (For example, 3. 028 +.0 03/ 009 has an upper limit of 3. 031 and a lower limit of 3. 019.) 2. Subtract the lower limit from the upper limit to get the...

Ngày tải lên: 21/07/2014, 15:20

... ASME/ANSI codes and standards subcommittees, including Y 14 Main Committee, Y 14 .3 Multiview and Sectional View Drawings, Y 14. 5 Dimensioning and Tolerancing, Y 14. 11 Molded Part Drawings, Y 14 .35 Drawing ... Linear and geometric dimensioning and tolerancing boundary example 4- 6 Chapter Four Figure 4 -3 Machined part made from casting Drawing Interpretation...

Ngày tải lên: 21/07/2014, 15:20

... calculation. Common raw material or stock parts. 16 .3. 3.2 Template Features Similar to template parts and assemblies, common features can be generated and put into libraries to be shared by all. ... Biometrika 52 (3 and 4) : 547 -558. 9. Ramberg, J.S., P.R. Tadikamalla, E.J. Dudewicz, E.F. Mykytha. 1979. A Probability Distribution and Its Uses in Fitting Data. Technometrics. 21(2)...

Ngày tải lên: 21/07/2014, 15:20

... 0.0 04 1.000-1 .49 9 0.09 544 417 0 .4 43 1 399 0.002 0.005 1.500-2.799 0.10186958 0 .45 00798 0.0025 0.006 2.800 -4. 499 0.1 43 9 9071 0 .40 445 47 0.0 03 0.008 4. 500-7.799 0.12976209 0 .4 43 1 399 0.0 04 0.01 7.800- 13. 599 ... 0 .45 747 142 0.001 0.0 04 1.000-1 .49 9 0.101 233 386 0 .44 7 230 08 0.0012 0.005 1.500-2.799 0.1180 030 2 0. 43 8 9869 0.0015 0.006 2.800 -4. 499 0.118 047...

Ngày tải lên: 21/07/2014, 15:20

... ) ( )( ) ( ) ( ) ( ) 46 8 23. 1/ 43 8 99.1 46 8 23. 1/1 46 537 .1/ 43 8 99.1 46 537 .1/1 46 8 23. 1/ 43 8 99.1 46 8 23. 1/1 15997. 43 8 99. 07202 .46 8 23. 15997. 43 8 99. 12576 .46 537 . 15997. 43 8 99. 07202 .46 8 23. 0025.0025.0015.015. BB B B TT TT       +      +       +=−−− The ... )                                   −− −−−  ...

Ngày tải lên: 21/07/2014, 15:20