STRESS ANALYSIS FOR PROCESS PIPING pps

... structure.   Piping deflections are within the limits. STRESS ANALYSIS FOR PROCESS PIPING CONTENTS:  INTRODUCTION TO STRESS - STRAIN RELATIONSHIP  WHAT IS STRESS ANALYSIS  PURPOSE OF PIPING STRESS ANALYSIS  ... establish the minimum requirements of stress analysis. PURPOSE OF PIPING STRESS ANALYSIS Purpose of piping stress analysis is to ensure:...

Ngày tải lên: 31/07/2014, 23:21

... Codes -Piping Code Impact on Design ASME B31.1 & B31.3 RULES FOR PIPE STRESS ANALYSIS -Design Criteria and Conditions, Types of Loadings and Stresses -Analysis Requirements for Sustained, ... PRESSURE PIPING CODES -Development of ASME B31 Piping Codes ASME B31.3 Process Piping Code (Design Philosophy, Intents, Contents, Coverages, Safeguards, etc.) -ASME B31....

Ngày tải lên: 31/07/2014, 23:21

... meet. 9 Perform all required formal and informal stress analysis. Stress analysis is the process of ensuring that the design the designers have developed will work. All the analysis in the ... 24 Piping Engineering Leadership for Process Plant Projects After the piping design group develops the tank, drum, or trayed tower layouts, these layouts are forwarded to the v...

Ngày tải lên: 02/04/2014, 16:20

... work [19]. Photographȱ©ȱTurismeȱdeȱBarcelonaȱ/ȱJ.ȱTrullàs Preliminaryȱcall for papers The 2011 European Signal Processing Conference (EUSIPCOȬ2011) is the nineteenth in a series of conferences promoted by the European Association for Signal Processing (EURASIP, ... fusion in networked systems. • Signal processing for communications. • Medical imaging and image analysis. • NonȬstationary...

Ngày tải lên: 21/06/2014, 11:20

... valid. 1.3 Preprocessing Before examining specific ICA algorithms, it is instructive to discuss preprocessing steps that are generally carried out before ICA. 1.3.1 Centering A simple preprocessing ... is unspecified. Formally, introducing a permutation matrix P and its inverse into the mix ing process in Equation 1. x = AP − 1 Ps = A � s � (15) 8 Independent Component Analysis for Audio...

Ngày tải lên: 29/06/2014, 13:20

... 535 Table 17-5 Combustible-Dependent Constants for Low-Strength Enclosures 552 Guidelines for Engineering Design for Process Safety CENTER FOR CHEMICAL PROCESS SAFETY of the AMERICAN INSTITUTE ... were written for engineers on the design team, the process hazard analysis team, and the people who make the basic decisions on plant design. Engineering desig...

Ngày tải lên: 03/07/2014, 12:20

... ABSTRACT In this study, GIS-based system analysis has been performed for the aim of monitoring and managing the sewerage lines. The model has been designed for a proper and efficient application, ... 2. For the future situation analysis, this is the main target of the study, as the first step the population for 30 years was estimated. To estimate population precisely, cens...

Ngày tải lên: 05/09/2013, 08:40

... system. Process 1-2 is an irreversible adiabatic compression process in the compressor 1. Process 2-3 is an absorbed heat process in the regenerator. Process 3-4 is an absorbed heat process ... chamber. Process 4-5 is an irreversible adiabatic expansion process in the turbine 1. Process 5-6 is an evolved heat process in the regenerator. Process 6-7 is an irreversible...

Ngày tải lên: 05/09/2013, 16:10

... the engine runs the analysis at a polynomial order of 3. You can then check stress and deformation results for structural analyses, or temperature gradient and flux results for thermal analyses. ... acceptable for example, the stress error estimates are too large—then switch to the multi-pass adaptive convergence strategy for subsequent design studies. Quick Check Define a...

Ngày tải lên: 12/12/2013, 12:15

Ngày tải lên: 13/12/2013, 03:15