SAT II History Episode 2 Part 2 docx

... location of a part to a mating part. The holes can have the 15- 12 Chapter Fifteen Fourth, it helps evaluate the usability of parts that are out of specification. For example, batches of parts may ... Biometrika 52( 3 and 4):547-558. 9. Ramberg, J.S., P.R. Tadikamalla, E.J. Dudewicz, E.F. Mykytha. 1979. A Probability Distribution and Its Uses in Fitting Data. Technometrics. 21 (2) :20 1...

Ngày tải lên: 21/07/2014, 15:20

... (in.) (in.) C .0600 .0016 .0 021 .0 028 .0 025 E . 120 0 .0016 .0 021 .0 028 .0 029 G . 120 0 .0016 .0 021 .0 028 .0 027 I .4500 .0046 .0064 .0083 .0088 J 3. 025 0 .0016 .0 021 .0 028 .0031 K .3000 .011 .015 .0197 ... equal P when combined using the RSS analysis from Chapter 9, Eq. (9.11). in. 022 . 0197.0 028 .0083.0 028 .0 028 .0 028 . 22 222 2 = +++++= Assy t We didn’t fully discuss th...

Ngày tải lên: 21/07/2014, 15:20

... abrasive. It is one of the newest manufactured abra- sives and 2 1 /2 times harder than alu- minum oxide. It can withstand tem- peratures up to 25 00 degrees Fahren- heit. CBN is produced by high tem- perature, ... is 90˚ 65˚ 45˚ 1 8 1v 8 1 8 1 8 T R T 60˚ 60˚ 60˚ 45˚ 45˚ EDC JG R = T 2 R = T 8 R = T 8 R = 3T 10 65˚ 65˚ 80˚ 80˚ 60˚ 23 ˚ 23 ˚ 60˚ R R R R T B T T A F R H T I T S K...

Ngày tải lên: 21/07/2014, 15:20

... remain parallel to the direction of broach travel. A couple of small broached parts are shown in Figure 14.3 14 .2. 1 Broaching Tools A broach is like a single point tool with many ‘points’ each ... up to and including the first FIGURE 14 .2: A large broach is shown (Courtesy Detroit Broach & Machine Co.) FIGURE 14.3: A couple of small broached parts are shown. (Courtesy Detroit Broach .....

Ngày tải lên: 21/07/2014, 15:20

... .26 2 × 4 RPM = = = 3 82 IPM 30.5 RPM 3 82 apr = = = .080 in. apr .080 N 8 apt = = = .010 in. SFPM 380 .26 2 × d .26 2 × 6 RPM = = = 24 2 IPM=apt×N×RPM = .006×10 24 2=14.5 Chap. 12: Milling Cutters ... . 024 π apr = apt = .006π apt = .006π FIGURE 12. 17: Drawing of a milling cutter showing the difference between advance per revolution (apr) and advance per tooth (apt). SFPM 400 .26...

Ngày tải lên: 21/07/2014, 15:20

... “hybrid.” O CH 2 CH CH 2 O O CH 2 CH CH 2 O CH 2 O Diglycidyl Ether of Novolac Resin CH 2 CH CH 2 O O CH 2 n R1 O CH 2 CH 2 O CH R2 HO Epoxy Resin Phenolic Crosslink Intermediate R2 O R1 O CH 2 OH CH + N C N H C NH NH 2 O CH 2 CH CH 2 O R O CH 2 CH CH 2 OH R N O CH 3 C CH 2 OH R NC N C NH O CH 2 CH CH 2 OH R + DICY ... O CH 2 OH CH + N C N H C NH NH 2...

Ngày tải lên: 21/07/2014, 15:20

... category ‘C’shape classification. 26 2 Costing designs //SYS21///INTEGRAS/B&H/PRS/FINALS_07-05-03/0750654376-CH003.3D – 24 9 – [24 9–300/ 52] 8.5 .20 03 8:56PM Part III Costing designs Procedures to ... use of the selection strategies and PRIMAs 24 5 //SYS21///INTEGRAS/B&H/PRS/FINALS_07-05-03/0750654376-CH0 02- 1.3D – 24 8 – [35 24 8 /21 4] 9.5 .20 03 2: 05PM Part- count optim...

Ngày tải lên: 21/07/2014, 16:21

... Mechanisms 9.1 Introduction 9 .2 Parallel Manipulators 9 .2. 1 Functional Requirements 9 .2. 2 Structural Characteristics 9 .2. 3 Enumeration of Planar Parallel Manipulators 9 .2. 4 Enumeration of Spherical ... 0-8493-0901-8 1. Machinery, Kinematics of. 2. Machine design. I. Title. II. Advanced topics in mechanical engineering series. TJ175 .T78 20 00 621 .8 ′11 dc21 00-05641...

Ngày tải lên: 21/07/2014, 17:20

... denotes a joint as outlined below. joint j B =      b 1,1 b 1 ,2 ··· b 1,m b 2, 1 b 2, 2 ··· b 2, m . . . . . . . . . . . . b n,1 b n ,2 ··· b n,m      link i where b ij =  1 if link i contains ... Journal of Mechanical De- sign, 120 , 2, 24 0 24 4. [14] Yan, H.S. and Chen, J.J., 1985, Creative Design of a Wheel Damping Mecha- nism, Mechanism and Machine Theory, 20 , 6, 597...

Ngày tải lên: 21/07/2014, 17:20

Ngày tải lên: 21/07/2014, 17:20