Process Selection - From Design to Manufacture Episode 2 Part 5 docx

Tài liệu Process Selection From Design to Manufacture P2 pdf

Tài liệu Process Selection From Design to Manufacture P2 pdf

... [F21] [W 12] [F1] [F5][F6][F8] [F10][A1] [A2][A4] [A5][A10] [W 12] [F1] [F10][A4] [A10] [F1] [A9][F13] [F14] [F 12] [F13] [F 12] [F13] [F16][F21] [F16][F18] [F21] [F18][F21] [W5][W 12] [F1][F2][F5] [F6] [F8][F10] [A2][A4][A5] [A7][A10] [W5][W 12] [F1][F2][A2] [A4][A5][A7] [A10] [F1][F2] [F13] [A9] [F14] [F 12] [F13] ... [F 12] [F13] [F 12] [F13] [F 15] [F17] [F21] [F 15] [F17] [F18][F21] [F...

Ngày tải lên: 20/01/2014, 00:20

10 383 0
Tài liệu Process Selection From Design to Manufacture P1 ppt

Tài liệu Process Selection From Design to Manufacture P1 ppt

... Manufacturing processes 24 0 2. 5 .2 Assembly syste ms 24 1 2. 5. 3 Joining processes 24 4 Part III Costing designs 24 9 3.1 Introduction 24 9 3 .2 Component costing 25 0 3 .2. 1 Development of the model 25 0 3 .2. 2 Basic ... the Designers’ Sandpit Project (GR/M53103 and GR/M 551 45) . K. G. Swift and J. D. Booker October 20 02 //SYS21///INTEGRAS/B&H/PRS/FINALS_0 7-0...

Ngày tải lên: 20/01/2014, 00:20

40 353 0
process selection - from design to manufacture

process selection - from design to manufacture

... casting 55 //SYS21///INTEGRAS/B&H/PRS/FINALS_0 7-0 5- 0 3/0 750 654 376-CH00 2- 1 .3D – 63 – [ 35 24 8 /21 4] 9 .5 .20 03 2: 05PM 2 Plastic and composite processing //SYS21///INTEGRAS/B&H/PRS/FINALS_0 7-0 5- 0 3/0 750 654 376-CH0 02. 3D ... processes //SYS21///INTEGRAS/B&H/PRS/FINALS_0 7-0 5- 0 3/0 750 654 376-CH00 2- 1 .3D – 66 – [ 35 24 8 /21 4] 9 .5 .20 03 2:...

Ngày tải lên: 02/04/2014, 16:25

333 486 0
Process Selection From design to manufacture P1 potx

Process Selection From design to manufacture P1 potx

... PRIMAs 24 0 2. 5. 1 Manufacturing processes 24 0 2. 5 .2 Assembly syste ms 24 1 2. 5. 3 Joining processes 24 4 Part III Costing designs 24 9 3.1 Introduction 24 9 3 .2 Component costing 25 0 3 .2. 1 Development ... model 25 0 3 .2. 2 Basic processing cost (P c ) 25 1 3 .2. 3 Relative cost coefficient (R c ) 25 3 3 .2. 4 Material cost (M c )27 2 3 .2. 5 Model validation...

Ngày tải lên: 03/07/2014, 12:20

30 308 0
Process Selection From design to manufacture P2 pptx

Process Selection From design to manufacture P2 pptx

... [W1][W2] [S1][S8] [W2][W3] [W9][W8] [W11][B1] [W2][W3] [W9][W11] [B1] [W3][W9] [S1][S8] [F20] [F19][F20] [F 22] [F19][F20] [F 22] [W1][W14] [S2][S6][S8] [S2][S3][S4] [S5][S7] [S9] [W2][W13] [W14][W19] [B4] [W2][W13] [W14][W19] [W13] [S2][S3][S6] [F 22] [F 22] [W2][W8] [W14][B2] [B4] [W2] [W2] [W1] [S2][S8] [W2][W8] [W11][W19] [B2] [W2][W11] [B2] [S2][S3][S6] [S8][F11] [F11] [F 22] [F 22]...

Ngày tải lên: 03/07/2014, 12:20

20 272 0
w