Dimensioning and Tolerancing Handbook Episode 1 Part 5 ppt

... Rule #1 mandates a ∅ .50 2 boundary of perfect form at MMC (envelope) Figure 5- 21 Rule #1 specifies a boundary of perfect form at MMC Geometric Dimensioning and Tolerancing 5 - 15 Table 5 -1 Geometric ... “size,” and those that don’t. Geometric Dimensioning and Tolerancing 5 -13 Figure 5- 8 Symbols used in dimensioning and tolerancing 5- 6 Chapter Five item...

Ngày tải lên: 21/07/2014, 15:20

... 2. 056 8E -11 1. 9327E -11 6.7 1. 816 0E -11 1. 7063E -11 1. 6032E -11 1. 50 62E -11 1. 4 15 0E -11 1. 3293E -11 1. 2487E -11 1. 1729E -11 1. 1 017 E -11 1. 0348E -11 6.8 9. 718 5E -12 9 .12 72E -12 8 .5 7 15 E -12 8.0493E -12 7 .55 85E -12 ... 1. 6 354 E- 01 1. 610 9E- 01 1 1. 58 66E- 01 1 .56 25E- 01 1 .53 86E- 01 1. 51 5 1E- 01 1.4 917 E- 01 1.4686E- 01 1.4 457 E-...

Ngày tải lên: 21/07/2014, 15:20

... A. Figure 5 -12 4 Two stacked single-segment feature control frames 5 -14 6 Chapter Five Figure 5 -13 4 Application of profile tolerances Geometric Dimensioning and Tolerancing 5 -13 5 Fig. 5 -12 6 shows ... extent. Figure 5 -12 5 Virtual condition boundaries of the upper frame for Fig. 5 -12 4 Figure 5 -12 6 Virtual condition boundaries of the lower frame for Fig....

Ngày tải lên: 21/07/2014, 15:20

... section 5. 6 .5 .1. Figure 5 -11 4 Bidirectional positional tolerancing, polar coordinate system 5 -11 0 Chapter Five Figure 5- 98 Applications of orientation tolerances 5 -11 8 Chapter Five Figure 5 -10 5 Establishing ... profile toler- ancing, as detailed in section 5 .13 .13 . Figure 5 -11 5 Positional tolerancing of a bounded feature Geometric Dimensioning and...

Ngày tải lên: 21/07/2014, 15:20

... egg in and out.) Geometric Dimensioning and Tolerancing 5 -10 1 Figure 5- 90 Three options for establishing the origin from a pattern of dowel holes Geometric Dimensioning and Tolerancing 5- 83 5. 9.9.2 ... clearances or “rattle” between a part and its functional gage.) Geometric Dimensioning and Tolerancing 5 -10 3 5. 9 .14 .2 Coaxial and Coplanar Features F...

Ngày tải lên: 21/07/2014, 15:20

... completion. Figure 5- 52 Establishing datum reference frames from part features Geometric Dimensioning and Tolerancing 5- 77 5. 9.8.4 Fixed-size TGC According to Table 5- 4, for features of size and bounded ... arm cover. And in fact, that’s the Figure 5- 54 Establishing datums on an engine cylinder head Figure 5- 53 Selection of datum features Geometric Dimensioning and...

Ngày tải lên: 21/07/2014, 15:20

... tolerance value. Geometric Dimensioning and Tolerancing 5- 53 LMC, it establishes a Level 2 virtual condition boundary as described in section 5. 6.3 .1 and Figs. 5 -17 (b) and 5 -18 (b). Alternatively, ... the appropriate plus or minus sign. .50 0 + .0 05 not .50 0 + .0 05 − .000 0 .50 0 ±.0 05 not .50 ±.0 05 . 750 not . 75 .748 .748 with not with 5. 7 ....

Ngày tải lên: 21/07/2014, 15:20

... METRIC Code Size Code Size A 8 .5 X 11 A4 210 X 297 B 11 X 17 A3 297 X 420 C 17 X 22 A2 420 X 59 4 D 22 X 34 A1 59 4 X 8 41 E 34 X 44 A0 8 41 X 11 89 4.6 Title Blocks The part of a drawing that has the ... section Figure 4 -14 Half section Drawing Interpretation 4- 21 Figure 4 - 15 Offset section Figure 4 -16 Broken-out section Geometric Dimensioning and Tolerancing 5- 3 •...

Ngày tải lên: 21/07/2014, 15:20

... ASME/ANSI codes and standards subcommittees, including Y14 Main Committee, Y14.3 Multiview and Sectional View Drawings, Y14 .5 Dimensioning and Tolerancing, Y14 .11 Molded Part Drawings, Y14. 35 Drawing ... Optimization Strategies 3-3 Figure 3 -1 Linear dimensioning and tolerancing boundary example Fig. 3-1g is showing a part made to its large size (like Fig. 3-1b), an...

Ngày tải lên: 21/07/2014, 15:20

... Repeatability and Reproducibility (GR&R) Calculations Gregory A. Hetland, Ph.D. 25 .1 Introduction 25 -1 25. 2 Standard GR&R Procedure 25 -1 25. 3 Summary 25- 7 25. 4 References 25- 7 Part 8 The ... Specification and Verification), ASME Y14 .5 (Dimensioning and Tolerancing) , and ASME Y14 .5. 2 (Certification of GD&T Professionals). 2 .1 Traditional Approac...

Ngày tải lên: 21/07/2014, 15:20