Dimensioning and Tolerancing Handbook Episode 1 Part 10 pot

... instead. Figure 5 -14 0 Profile tolerancing to control a combination of characteristics 5 .13 .11 .1 With Positional Tolerancing for Bounded Features Profile tolerancing can be teamed with positional tolerancing ... runout tolerance will apply and be careful not to rob any feature of usable and needed tolerance. Geometric Dimensioning and Tolerancing 5 -15 1 Figure 5 -13 7...

Ngày tải lên: 21/07/2014, 15:20

... METRIC Code Size Code Size A 8.5 X 11 A4 210 X 297 B 11 X 17 A3 297 X 420 C 17 X 22 A2 420 X 594 D 22 X 34 A1 594 X 8 41 E 34 X 44 A0 8 41 X 11 89 4.6 Title Blocks The part of a drawing that has the ... section Figure 4 -14 Half section Drawing Interpretation 4- 21 Figure 4 -15 Offset section Figure 4 -16 Broken-out section Geometric Dimensioning and Tolerancing 5-3 • ASME Y1...

Ngày tải lên: 21/07/2014, 15:20

... Biometrika 52(3 and 4):547-558. 9. Ramberg, J.S., P.R. Tadikamalla, E.J. Dudewicz, E.F. Mykytha. 19 79. A Probability Distribution and Its Uses in Fitting Data. Technometrics. 21( 2):2 01- 214 . 10 . Stoddard, ... server. QUIT leaves the FTP program. Automating the Tolerancing Process 15 -11 15 .5 .1. 2 Database Administration The database form, organization, and location must be...

Ngày tải lên: 21/07/2014, 15:20

... constrains the ball’s location Figure 5 -11 1 Bidirectional positional tolerancing, rectangular coordinate system Geometric Dimensioning and Tolerancing 5 -10 9 5 .10 .6 The 24 Cases So far, in this section ... section 5.6.5 .1. Figure 5 -11 4 Bidirectional positional tolerancing, polar coordinate system 5 -11 0 Chapter Five Figure 5-98 Applications of orientation tolerances 5 -11...

Ngày tải lên: 21/07/2014, 15:20

... clearances or “rattle” between a part and its functional gage.) Geometric Dimensioning and Tolerancing 5 -10 3 5.9 .14 .2 Coaxial and Coplanar Features Fig. 5 -13 1 shows another example of separate ... let the egg in and out.) Geometric Dimensioning and Tolerancing 5 -10 1 Figure 5-90 Three options for establishing the origin from a pattern of dowel holes Geometric Dim...

Ngày tải lên: 21/07/2014, 15:20

... interpret all dimen- sions and tolerances, including the circularity tolerance, as applying in the free state. The standard Geometric Dimensioning and Tolerancing 5- 71 On the other hand, if we allow each ... freedom between the cover and the TGC system 5-66 Chapter Five Figure 5-57 Methods of applying datum feature symbols Geometric Dimensioning and Tolerancing 5-59 5.8 .10...

Ngày tải lên: 21/07/2014, 15:20

... tolerance value. Geometric Dimensioning and Tolerancing 5-53 LMC, it establishes a Level 2 virtual condition boundary as described in section 5.6.3 .1 and Figs. 5 -17 (b) and 5 -18 (b). Alternatively, ... Five Eliminate unnecessary trailing zeros. 25 .1 not 25 .10 12 not 12 .0 with not with The exceptions are limit dimensions and bilateral (plus and minus) tolerances, w...

Ngày tải lên: 21/07/2014, 15:20

... Rule #1 mandates a ∅.502 boundary of perfect form at MMC (envelope) Figure 5- 21 Rule #1 specifies a boundary of perfect form at MMC Geometric Dimensioning and Tolerancing 5 -15 Table 5 -1 Geometric ... “size,” and those that don’t. Geometric Dimensioning and Tolerancing 5 -13 Figure 5-8 Symbols used in dimensioning and tolerancing 5-6 Chapter Five items as Sheetrock...

Ngày tải lên: 21/07/2014, 15:20

... ASME/ANSI codes and standards subcommittees, including Y14 Main Committee, Y14.3 Multiview and Sectional View Drawings, Y14.5 Dimensioning and Tolerancing, Y14 .11 Molded Part Drawings, Y14.35 Drawing ... Optimization Strategies 3-3 Figure 3 -1 Linear dimensioning and tolerancing boundary example Fig. 3-1g is showing a part made to its large size (like Fig. 3-1b), and t...

Ngày tải lên: 21/07/2014, 15:20

... Specification and Verification), ASME Y14.5 (Dimensioning and Tolerancing) , and ASME Y14.5.2 (Certification of GD&T Professionals). 2 .1 Traditional Approaches to Dimensioning and Tolerancing Engineering, ... 19 96. Company Update. 8. National Institute of Standards and Technology. 19 98. U.S. Department of Commerce. 9. National Institute of Standards and Technolo...

Ngày tải lên: 21/07/2014, 15:20