Dimensioning and Tolerancing Handbook Episode 2 Part 2 pot

... ACTUAL 1 .25 2±.004 .24 8 .0 02 Ø.010 0 0 0 2 .24 8 Ø.010 625 623 -1.315 -1. 321 006 3 .24 8 Ø.010 +.0 02 X X X .25 2±.004 .25 2±.004 .25 0 .25 0 .25 0 .0 02 .0 02 0 0 0 . 625 .630 +.005 -1.315 -1. 320 005 Figure ... 1 .4 82 .0 02 .480 .4 82 .0 02 Ø.009 2. 200 2. 203 +.003 0 0 0 2 . 4 82 .0 02 .480 .483 .003 Ø.010 - .900 - .905 1.318 1....

Ngày tải lên: 21/07/2014, 15:20

... 1 -2 Graphical definition of short- term Six Sigma performance for a single characteristic 2- 6 Chapter Two 2. 2 .2. 4 Geometric Dimensioning and Tolerancing (GD&T) Geometric dimensioning and tolerancing ... product and service. 2. Adopt the new philosophy. xx Contents Chapter 25 : Gage Repeatability and Reproducibility (GR&R) Calculations Gregory A. Hetland, P...

Ngày tải lên: 21/07/2014, 15:20

... extent. Figure 5- 125 Virtual condition boundaries of the upper frame for Fig. 5- 124 Figure 5- 126 Virtual condition boundaries of the lower frame for Fig. 5- 124 Geometric Dimensioning and Tolerancing ... datums. 2. Copy only the primary datum and its modifier (if any). 3. Copy the primary and secondary datums and their modifiers, in order. 4. Copy the primary, secondary, an...

Ngày tải lên: 21/07/2014, 15:20

... METRIC Code Size Code Size A 8.5 X 11 A4 21 0 X 29 7 B 11 X 17 A3 29 7 X 420 C 17 X 22 A2 420 X 594 D 22 X 34 A1 594 X 841 E 34 X 44 A0 841 X 1189 4.6 Title Blocks The part of a drawing that has the highest ... Broken-out section Geometric Dimensioning and Tolerancing 5-3 • ASME Y14.5M-1994, Dimensioning and Tolerancing • ASME Y14.5.1M-1994, Mathematical Definition of Dim...

Ngày tải lên: 21/07/2014, 15:20

... assemblies. ASME Y14.5M-1994 (the Dimensioning and Tolerancing standard) and the ASME Y14.5.1M-1994 (the standard on Mathematical Principles of Dimensioning and Tolerancing) both state that occasionally ... interna- tional, and industrial standards research and development efforts in the areas of global tolerancing of mechanical parts and supporting metrology. Dr. Hetlan...

Ngày tải lên: 21/07/2014, 14:26

... Point 124 Transformation Matrix 20 2 Angular Dimension 20 6 Diameter Dimension 21 0 General Label 21 2 General Note 21 4 Leader (Arrow) 21 6 Linear Dimension 21 8 Ordinate Dimension 22 2 Radius Dimension 22 8 ... tolerance) /2) / standard deviation of process sigma = (SQRT(LN(1/dpo) ^2) ))- (2. 515517 + 0.8 028 53 * (SQRT(LN(1/dpo) ^2) )) + 0.010 328 * (SQRT(LN(1/dpo) ^2) )) ^2) /(1...

Ngày tải lên: 21/07/2014, 15:20

... any sample handle. Figure 5-116 Standard catalog handle Geometric Dimensioning and Tolerancing 5- 123 relative only to the DRF plane that is perpendicular to the dimension line. The . 020 tolerance, ... Subsequent chapters, particularly 22 and 24 , present a more thorough discussion of positional tolerance calculations. 5.11.7.1 Single-Segment Feature Control Frame The handle shown...

Ngày tải lên: 21/07/2014, 15:20

... in and out.) Geometric Dimensioning and Tolerancing 5-101 Figure 5-90 Three options for establishing the origin from a pattern of dowel holes Geometric Dimensioning and Tolerancing 5-83 5.9.9 .2 ... with your hands the clearances or “rattle” between a part and its functional gage.) Geometric Dimensioning and Tolerancing 5-103 5.9.14 .2 Coaxial and Coplanar Features...

Ngày tải lên: 21/07/2014, 15:20

... completion. Figure 5- 52 Establishing datum reference frames from part features Geometric Dimensioning and Tolerancing 5-77 5.9.8.4 Fixed-size TGC According to Table 5-4, for features of size and bounded ... interpret all dimen- sions and tolerances, including the circularity tolerance, as applying in the free state. The standard Geometric Dimensioning and Tolerancing 5-71...

Ngày tải lên: 21/07/2014, 15:20

... point and one or more trailing zeros to some values. Plus and minus tolerances are each expressed with the appropriate plus or minus sign. 25 .45 not 25 .45 25 .00 25 32 + 0 .25 not 32 + 0 .25 ... Chapter Five Eliminate unnecessary trailing zeros. 25 .1 not 25 .10 12 not 12. 0 with not with The exceptions are limit dimensions and bilateral (plus and minus) tol...

Ngày tải lên: 21/07/2014, 15:20