Dimensioning and Tolerancing Handbook Episode 2 Part 10 docx

... Biometrika 52( 3 and 4):547-558. 9. Ramberg, J.S., P.R. Tadikamalla, E.J. Dudewicz, E.F. Mykytha. 1979. A Probability Distribution and Its Uses in Fitting Data. Technometrics. 21 (2) :20 1 -21 4. 10. Stoddard, ... Guidelines This book is titled as a dimensioning and tolerancing handbook. The chapter so far has delivered suggestions associated with electronic data; how to use it,...

Ngày tải lên: 21/07/2014, 15:20

... 6, ( )( ) ( )( ) ( )( ) ( )( ) ( )( ) ( )( ) in. 0 028 1. 0 025 .100 0357 .100 106 .100 0357 .100 0357 .100 0357.1 22 222 2 = +−++++= Assy σ and ( ) in01685. 0 028 1.0.6 6 = =P Predicting Assembly Quality (Six Sigma ... )( ) ( )( )( ) ( )( )( ) ( )( )( ) ( )( )( ) in. 00335. 0 025 .18. 1100 0357.33. 1100 106 .27 .11 000357.13. 1100 0357 .22 . 1100 0357.05.11 22 2 22 2 = +−++ ++ = DAssy σ...

Ngày tải lên: 21/07/2014, 15:20

... Model: ( ) ( ) ( ) 2 13 2 12 2 11 2 eScSaST ASM δδδ ++= ( ) ( )( )( ) ( )( )( ) )7909 32( )4500 82( 2 )7909 32( 2 2 222 627 221 01869645008 646 920 14 922 779093 627 22 )0004)(548 310( )646 92( )017453( ./. ./ da ... ) ( )( )( ) ( )( )( ) ( )( )( ) 22 2 2 13 2 12 2 11 0008. 627 2 .20 004.5483 .100 04.6469 .2 +−+−= ++= eScSaS δδδ ( )( ) ( )( ) ( )( ) 0008 627 220 004548...

Ngày tải lên: 21/07/2014, 15:20

... .0 025 4 .0081 C * * .0 025 * .0 025 * .0 025 * D 1.00 .0 720 2 .46 823 .0 02 .001736 .00637 E 1.00 . 125 76 .46537 .006 .0 024 98 .007 92 F 1.00 .0 720 2 .46 823 .0 02 .001736 .00637 G * * .0 025 * .0 025 * .0 025 * Assembly ... ]                                   ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂ ∂...

Ngày tải lên: 21/07/2014, 15:20

... ) 1331. 8805. 125 .14741. 625 .1875. 8805. 4741. 125 .1700.1 625 .3 4741. 125 .18805. 625 .1875. 8805. 4741. 125 .1700.1 625 .3 625 .2 8805. 125 .14741. 625 .1875. 8805. 4741. 125 .1700.1 625 .3 cossin cos sin sincos cos sin cossin cos sin 2 22 2 22 22 2 22 2 22 22 −=                         +      +− − −+         +       +− − −− − ...

Ngày tải lên: 21/07/2014, 15:20

... 2. 3852E- 02 2. 329 6E- 02 2 2. 2750E- 02 2 .22 16E- 02 2.1692E- 02 2.1178E- 02 2.0675E- 02 2.0182E- 02 1.9699E- 02 1. 922 6E- 02 1.8763E- 02 1.8309E- 02 2.1 1.7865E- 02 1.7 429 E- 02 1.7003E- 02 1.6586E- 02 1.6177E- 02 1.5778E- 02 ... 3.5148E- 02 3.4380E- 02 3.3 625 E- 02 3 .28 84E- 02 3 .21 57E- 02 3.1443E- 02 3.0742E- 02 3.0054E- 02 2.9379E- 02 1.9 2. 8717E- 0...

Ngày tải lên: 21/07/2014, 15:20

... ) ( ) 2 1 22 222 222 2 22 222 222 222 2 22 222 222 2 0300.)1(8.0060.)1(8.0070.)1(8. 0075.)1 (2. 0050.)1(8.0070.)1 (2. 0050.)1(8. 0075.)1 (2. 0030.)1(8.0 020 .)1 (2. 0155).1 (2. 0300).1 (2. 0060).1 (2. 0070).1 (2. 0075).1(8.0050).1 (2. 0070).1(8. 0050).1 (2. 0075).1(8.0030).1 (2. 0 020 ).1(8.0155).1(8.             +−+ ++++ ++++− ++−++++ +++++−= ems t t ems ... = .04 72 1 )11...

Ngày tải lên: 21/07/2014, 15:20

... shown in Figs. 8-1, 8 -2, and 8-3. Statistical tolerance requirements can be indicated in the ST frame in one of the three ways defined in sections 8 .2. 1, 8 .2. 2, and 8 .2. 3. 8 .2. 1 Using Process Capability ... modification, review, and voting by ISO, and should not be taken as the final standard on statistical tolerancing. 8 .2 Specification of Statistical Tolerancing Stati...

Ngày tải lên: 21/07/2014, 15:20

... positional tolerancing and the pattern location by positional tolerancing, each requirement shall be met independently. (#5458, 4 .2) 16±0.5 20 20 16±0.5 64X 0 ,2 30 30 ZY A 0 ,2 0 ,2 15 15 Y Z ZY A 0 .2 0 .2 True ... drawing view, and indicated in the tolerance frame by the symbol placed after the tolerance value. (# 1101 ,11; #105 78,4) BA 0, 02 P P 22 5 8X 25 40 A 6X M2...

Ngày tải lên: 21/07/2014, 15:20

... dimensioning and tolerancing standards. ASME publishes a single standard that explains all dimensioning and tolerancing topics. ISO publishes multiple standards on subsets of dimensioning and tolerancing ... Y14.5M-1994. 6 .2. 3 .2 ISO The ISO standards referenced in Tables 6-6 through 6-13 are: ISO 1101 -1983 ISO 8015-1985 ISO 105 78-19 92 ISO 1660-1987 ISO 5458-1987 ISO...

Ngày tải lên: 21/07/2014, 15:20