Dimensioning and Tolerancing Handbook Episode 3 Part 2 doc

... ACTUAL 1 .25 2±.004 .24 8 .0 02 Ø.010 0 0 0 2 .24 8 Ø.010 625 6 23 -1 .31 5 -1 . 32 1 006 3 .24 8 Ø.010 +.0 02 X X X .25 2±.004 .25 2±.004 .25 0 .25 0 .25 0 .0 02 .0 02 0 0 0 . 625 . 630 +.005 -1 .31 5 -1 . 32 0 005 Figure ... 1 .4 82 .0 02 .480 .4 82 .0 02 Ø.009 2. 200 2. 2 03 +.0 03 0 0 0 2 . 4 82 .0 02 .480 .4 83 .0 03 Ø.010 - .900 - .9...

Ngày tải lên: 21/07/2014, 15:20

... assemblies. ASME Y14.5M-1994 (the Dimensioning and Tolerancing standard) and the ASME Y14.5.1M-1994 (the standard on Mathematical Principles of Dimensioning and Tolerancing) both state that occasionally ... interna- tional, and industrial standards research and development efforts in the areas of global tolerancing of mechanical parts and supporting metrology. Dr. Hetlan...

Ngày tải lên: 21/07/2014, 14:26

... .31 2 .0 03 .30 9 .31 1 .0 02 Ø.0 12 1.500 1.5 03 +.0 03 2 .500 2 .501 +.001 2 .31 2 .0 03 .30 9 .31 3 .004 Ø.014 1.500 1.505 1 .000 .998 - .0 02 3 .31 2 .0 03 ... 3 .31 2 .0 03 .30 9 .31 2 .0 03 Ø.0 13 4 .500 .496 2 .500 2 .497 - .0 03 4 .31 2 .0 03 .30 9 .31 0 .001 Ø.011 4...

Ngày tải lên: 21/07/2014, 15:20

... 1 -2 Graphical definition of short- term Six Sigma performance for a single characteristic 2- 6 Chapter Two 2. 2 .2. 4 Geometric Dimensioning and Tolerancing (GD&T) Geometric dimensioning and tolerancing ... product and service. 2. Adopt the new philosophy. xx Contents Chapter 25 : Gage Repeatability and Reproducibility (GR&R) Calculations Gregory A. Hetland, P...

Ngày tải lên: 21/07/2014, 15:20

... any sample handle. Figure 5-116 Standard catalog handle Geometric Dimensioning and Tolerancing 5-1 23 relative only to the DRF plane that is perpendicular to the dimension line. The . 020 tolerance, ... composite profile toler- ancing, as detailed in section 5. 13. 13. Figure 5-115 Positional tolerancing of a bounded feature Geometric Dimensioning and Tolerancing 5-107 A posi...

Ngày tải lên: 21/07/2014, 15:20

... Fig. 5- 63( b), our first alignment step remains the same. We still optimize orientation of the TGC system to datum feature A. However, now Geometric Dimensioning and Tolerancing 5- 63 5.9 .2. 2 Functional ... interpret all dimen- sions and tolerances, including the circularity tolerance, as applying in the free state. The standard Geometric Dimensioning and Tolerancing 5-71 On...

Ngày tải lên: 21/07/2014, 15:20

... MMC Allowable Position Tolerance 2. 74 0.00 0.14 2. 76 0. 02 0.16 2. 78 0.04 0.18 2. 80 0.06 0 .20 2. 82 0.08 0 .22 2. 84 0.10 0 .24 2. 86 0. 12 0 .26 Tolerancing Optimization Strategies 3- 7 The tolerance progression ... designer’s expectations. Fig. 3- 2e shows a combination of Figs. 3- 2b and 3- 2c (like Figs. 3- 1b and 3- 1c), in that it allows the shape to be small...

Ngày tải lên: 21/07/2014, 15:20

... 5- 125 Virtual condition boundaries of the upper frame for Fig. 5- 124 Figure 5- 126 Virtual condition boundaries of the lower frame for Fig. 5- 124 Geometric Dimensioning and Tolerancing 5- 133 Figure ... A. Figure 5- 124 Two stacked single-segment feature control frames 5-146 Chapter Five Figure 5- 134 Application of profile tolerances Geometric Dimensioning and Tolerancing 5...

Ngày tải lên: 21/07/2014, 15:20

... in and out.) Geometric Dimensioning and Tolerancing 5-101 Figure 5-90 Three options for establishing the origin from a pattern of dowel holes Geometric Dimensioning and Tolerancing 5- 83 5.9.9 .2 ... the clearances or “rattle” between a part and its functional gage.) Geometric Dimensioning and Tolerancing 5-1 03 5.9.14 .2 Coaxial and Coplanar Features Fig. 5- 131...

Ngày tải lên: 21/07/2014, 15:20

... point and one or more trailing zeros to some values. Plus and minus tolerances are each expressed with the appropriate plus or minus sign. 25 .45 not 25 .45 25 .00 25 32 + 0 .25 not 32 + 0 .25 ... external); 2) the feature’s size limits; and 3) the specified geometric tolerance value. Figure 5 - 32 Resultant condition boundary for the ∅.514 hole in Fig. 5 -30 Geometri...

Ngày tải lên: 21/07/2014, 15:20