Designation: C 474 – 97 - Joint Treatment Materials for Gypsum Board Construction1 potx
Designation: C 474 – 97 - Joint Treatment Materials for Gypsum Board Construction1 potx
... Build- ing Materials and Systems 2 C 36 Specification for Gypsum Wallboard 2 C 472 Test Methods for Physical Testing of Gypsum, Gyp- sum Plasters, and Gypsum Concrete 2 C 475 Specification for Joint ... without FIG. 3 Arrangement for Length Expansion Measurement C 474 5 Designation: C 474 – 97 Standard Test Methods for Joint Treatment Materials fo...
Ngày tải lên: 10/07/2014, 23:20
Designation: C 141 – 97 - Hydraulic Hydrated Lime for Structural Purposes1 pptx
... Lime 2 C 109 Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or 50-mm Cube Specimens) 2 C 150 Specification for Portland Cement 2 C 151 Test Method for Autoclave Expansion ... Portland Cement 2 C 184 Test Method for Fineness of Hydraulic Cement by the 15 0- m (No. 100) and 7 5- µm (No. 200) Sieves 2 C 187 Test Method for Normal Consistency...
Ngày tải lên: 10/07/2014, 23:20
Designation: C 475 – 94 Standard Specification for Joint Compound and Joint Tape for Finishing docx
... Methods for Joint Treatment Materials for Gyp- sum Board Construction 2 3. Terminology 3.1 Definitions—Definitions shall be in accordance with Terminology C 11. 3.2 Definitions of Terms Speci c to ... Methods C 474. 4.2 Joint Compounds. 4.2.1 Check Cracking—No cracks in the thinner half of the wedge and no deep fissure cracks in the thicker half of the wedge. 4.2.2 Putrefacti...
Ngày tải lên: 10/07/2014, 23:20
Designation: C 5 – 79 (Reapproved 1997) - Quicklime for Structural Purposes1 pot
... Sampling, Inspection, etc. 7.1 The sampling, inspection, rejection, retesting, packing, and marking shall be conducted in accordance with Methods C 50. 8. Test Methods 8.1 Conformance to chemical requirements ... deter- mined in accordance with Test Methods C 25. 8.2 Conformance to plasticity and residue requirements shall be determined in accordance with Test Methods C 110. 9. Keywords...
Ngày tải lên: 10/07/2014, 23:20
Designation: C 183 – 97 - Sampling and the Amount of Testing of Hydraulic Cement1 pps
... non-conformance of cements with requirements of purchase specifications. 4.2 This practice is referenced as the procedure for sampling masonry cement (Specification C 91), portland cement (Speci- fication ... r¯. Compute the average range, r¯, for each included physical and chemical property limited by specification requirements. 9.5.2 Critical Limit—Calculate the critical limit, C, for...
Ngày tải lên: 10/07/2014, 23:20
Designation: C 226 – 96 - Air-Entraining Additions for Use in the Manufacture pot
... specifica- tion in accordance with the methods prescribed in Sections 7-1 1. 7. Tests on Cement 7.1 Test the cement samples in accordance with the follow- ing methods: 7.1.1 Chemical Analysis of Cement—Test ... be calculated the potential percentages of the following compounds: tricalcium silicate, dicalcium silicate, tricalcium aluminate, and tetracalcium alu- minoferrite. Determinations...
Ngày tải lên: 10/07/2014, 23:20
Designation: C 348 – 97 - Flexural Strength of Hydraulic-Cement Mortars1 pptx
... of Hydraulic Cement 2 C 305 Practice for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency 2 C 349 Test Method for Compressive Strength of Hydraulic Cement Mortars ... Referenced Documents 2.1 ASTM Standards: C 109 /C 109M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or 50-mm Cube Specimens) 2 C 230 Specification fo...
Ngày tải lên: 10/07/2014, 23:20
Designation: C 349 – 97 - Compressive Strength of Hydraulic-Cement Mortars ppt
... Method C 348. The compressive strength values are for reference purposes, and not as substitutes for values (using 50-mm (2-in.) cubes) obtained by Test Method C 109 /C 109M for cement acceptance. 2 4. ... use. 2. Referenced Documents 2.1 ASTM Standards: C 109 /C1 09M Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or 50-mm Cube Specimens) 2 C 34...
Ngày tải lên: 10/07/2014, 23:20
Designation: C 490 – 00a - Use of Apparatus for the Determination docx
... Testing of Hydraulic Cements and Concretes 2 C 1005 Specification for Reference Masses and Devices for Determining Mass and Volume for Use in the Physical Testing of Hydraulic Cements 2 3. Terminology 3.1 ... for checking the FIG. 1 Molds (SI Units) C 490 2 Designation: C 490 – 00a Standard Practice for Use of Apparatus for the Determination of Length Change of Hardened...
Ngày tải lên: 10/07/2014, 23:20