Part 1: Code of practice for design — Rolled and welded sections pptx

... ºC a — –30 ºC a — — M— –30 ºC a — — –30 ºC a — ML — –50 ºC — — — –50 ºC — N— –30 ºC a — –30 ºC a –30 ºC a — NL — –50 ºC — — –50 ºC –50 ºC — Q — –20 ºC b — — QL — — –40 ºC b — — QL1 — — –60 ... construction — Section 3 .1: Code of practice for design of simple and continuous composite bea...

Ngày tải lên: 08/07/2014, 22:20

... materials and workmanship: cold formed sections and sheeting. BS 6399-1, Loading for buildings Ð Code of practice for dead and imposed loads. BS 6399-2, Loading for buildings Ð Code of practice for ... properties of fasteners Ð Bolts, screws and studs. CP3 Code of basic data for the design of buildings: Chapter V: Part 2: Wind loads. 1.4 Terms and...

Ngày tải lên: 08/07/2014, 22:20

... 3.4 and 3.5 of BS 8110 -1:1 985 or Tables 5.1 and 5.2 of BS 8110-2:1985. Figure 4 — Typical profiles BRITISH STANDARD BS 5950-4: 1994 Structural use of steelwork in building — Part 4: Code of practice ... required for overall stability, even when some or all of the structural design and detailing of those parts and components is carried out by another...

Ngày tải lên: 08/07/2014, 22:20

... R t,0.5 and R m should normally be taken as specified in the relevant product standard for the steel sheet or strip and used for the formed sections. For information, the resulting values of Y s and ... : Part 6 : 1995 Issue 2, January 1999 Section 3 Section 3. Properties of materials and section properties 3.1 Range of thicknesses The provisions of this Part of B...

Ngày tải lên: 08/07/2014, 22:20

... Specification for SI units and recommendations for the use of their multiples and of certain other units BS 6399 : Loading for buildings BS 6399 : Part 2 : 1995 Code of practice for wind loads BS 6399 : Part ... 6399 : Part 1 : 1996 Code of practice 1 Scope 1.1 This Part of BS 6399 gives dead and minimum recommended imposed loads for use in designing...

Ngày tải lên: 08/07/2014, 22:20

... construction; — Section 3 .1: Code of practice for design of simple and continuous composite beams; — Section 3.2 1) : Code of practice for design of composite columns and frames; — Part 4: Code of practice ... practice for design of floors with profiled steel sheeting; — Part 5: Code of practice for design in cold form...

Ngày tải lên: 08/07/2014, 22:20

... 0.525 — 0.2 0.390 0.516 0.634 0.744 0.862 1.035 1.329 — — 0.3 0.872 1.088 1.284 1.476 1.741 — — — — 0.4 1.553 1.849 2.105 2.412 — — — — — 0.5 2.400 2.713 — — — — — — — 0.6 3.278 — — — — — — — — 40° ... 0.142 — 0.2 0.076 0.089 0.083 0.072 0.082 0.137 0.281 — — 0.3 0.137 0.130 0.102 0.093 0.151 —...

Ngày tải lên: 08/07/2014, 22:20

... flat roofs 32 Figure 18 — Key for inset storey 32 Figure 19 — Key for monopitch roofs 33 Figure 20 — Key for duopitch roofs 34 Figure 21 — Key for hipped roofs 37 Figure 22 — Key for mansard and ... multipitch roofs 38 Figure 23 — Key for multi-bay roofs 39 Figure 24 — Key for free-standing canopy roofs 42 Figure 25 — Reduction factor for leng...

Ngày tải lên: 08/07/2014, 22:20

... loads. CP 3, Code of basic data for the design of buildings 1) . CP 3: Chapter V, Loading. ISO 3898, Bases for design of structures — Notations — General symbols 1) . ISO 4355, Bases for design of structures ... Specification for SI units and recommendations for the use of their multiples and of certain other units 1) . BS 6399, Loading for buildin...

Ngày tải lên: 08/07/2014, 22:20

... Agriculture, Department of Environment, Department for Planning and Infrastructure, Department of Health and Local Government have developed this Environmental Code of Practice for the Poultry Industries ... Welfare of Animals: Land Transport of Poultry, available from the Internet site <www.publish.csiro.au> ;and the Department of Local Government and Regional...

Ngày tải lên: 17/03/2014, 10:20