Autodesk Revit Architecture 2011 No Experience Required - part 51 pps

... Railings 482 FIGURE 10.61 Specifying two balusters per tread and no actual posts You may or may not have noticed that we did not get the opportunity to change the baluster’s material as we did ... 10.63. 7. Moving down the list, change Monolithic Material to Wood - Mahogany. 8. Change Nosing Profile to Stair Nosing : Stair Nosing (see Figure 10.63). 9. Under the Risers category, chan...

Ngày tải lên: 07/07/2014, 08:20

... open Revit Architecture, click the icon on your desktop (see Figure 1.1), or choose Start ➢ All Programs ➢ Autodesk ➢ Autodesk Revit Architecture 2011 ➢ Autodesk Revit Architecture 2011 (see ... relinquish. Introduction xxii Who Should Read This Book Autodesk ® Revit ® Architecture 2011: No Experience Required. Does that mean if you have used Revit yo...

Ngày tải lên: 07/07/2014, 07:20

... the view NOTE If you had floors already placed in the model, Revit would cre- ate the interior elevation to only extend to this geometry. Since we do not have floors, Revit does not know where ... and you turned the shadows on. Normally, in an interior elevation you do not want to do this. Revit allows you to have separate view properties on a view-by-view basis. To access the View...

Ngày tải lên: 07/07/2014, 08:20

... well aware, you’ll use the Rotate command quite frequently. Now that you have some experience with the Rotate command and know how Revit wants you to move the pivot point, the next command, ... mislead- ing. You are not actually “moving” anything. If you choose Move To: Last, for example, Revit will place an additional item in the last place you pick, keeping the first item intact....

Ngày tải lên: 07/07/2014, 08:20

... with. If you did not complete the previous chapter, go to the book’s web page at www.sybex.com/go/ revit2 011ner. From there you can browse to Chapter 6 and find the file called NER-20.rvt. Your ... row You are now in the Edit Assembly dialog, as you were in the previous procedure. The objective now is to add 1 ″ terrazzo flooring to the top of the 6″ of concrete. Adding a Layer Now it’s tim...

Ngày tải lên: 07/07/2014, 08:20

... base When you have suc- cessfully mitered a corner and are ready to move to the next, there is nothing indi- cating that you can safely pick another corner. You do not need it. When you ... n g ! Sometimes Revit does not like you hacking up its perfectly fine walls. The warning shown in the following image is common and has no effect on the model. You can just ignore it. Viewing ....

Ngày tải lên: 07/07/2014, 08:20

... form the canopy, as shown in Figure 8.40. NOTE The support you pick first determines the direction that the beams will run in. Notice the double lines in the horizontal beam? This indi- cates ... Completing the framing for the canopy Adding a Beam System Although adding beam systems is much more crucial in Revit Structure, it does have its usefulness in Revit Architecture as well....

Ngày tải lên: 07/07/2014, 08:20

... how we can cre- ate our own. Notation and symbols are the basis for maintaining CAD standards. If you simply use the examples given to you by Revit, you will have a set of draw- ings that look ... If you decide to change the note in the materials, it will update every occurrence in the entire model. FIGURE 11.75 The material is now tagged with a leadered note. Chapter 11 • Schedules ... t...

Ngày tải lên: 07/07/2014, 08:20

... the Div 04-Masonry folder. 4. Go to the 041200-Clay Unit Masonry folder. 5. Select the Bricks-Top.rfa file. 6. Click Open. 7. When the file is loaded, select Bricks-Top : Standard - 3/8 ″ Joint ... mentioned before, Revit provides a good number of 2D details that we can insert at any time. When Revit does not have the component we need, we can always cre- ate one. It is not that...

Ngày tải lên: 07/07/2014, 08:20

... ? Notice that when you clicked the Save icon, Revit did not just save over the origi- nal file. You are forced to do a Save As. You have one of three choices here: If the file is not write-protected ... Gray tile, as shown in Figure 12.26. (The color is actually RGB 19 2-1 9 2-1 92.) FIGURE 12.26 Selecting the gray color (RGB 19 2-1 9 2-1 92) 10. Click OK twice. 11. On the Draw p...

Ngày tải lên: 07/07/2014, 08:20