Autodesk Revit Architecture 2011 No Experience Required - part 4 pdf

... Chapter 1 • The Revit World 4 4. In the upper-left corner of the Revit window, you will see a big purple R. Click the purple R and choose ... You may also notice that Revit places an additional Options bar below the Ribbon for more choices. FIGURE 1.6 The Ribbon is the backbone of Revit Architecture. Chapter 1 • The Revit World 6 FIGURE ... in Revit. The Revit Architectu...

Ngày tải lên: 07/07/2014, 07:20

... 44 3 44 5 cursor, 44 1 44 3, 48 7 customization, 48 3 49 6 Element Properties, 44 2 families, 47 7 47 9 landings, 44 2 45 2 Level 1, 44 1 Level 2, 44 1 magenta lines, 48 7 railings, 44 5 46 1 Rise/Run method, 44 0 46 1 systems ... view, 48 7 48 8 winding staircase, 46 1 47 9 Annotate tab, 46 3 cursor, 46 4 Detail Line button, 46 3 railings, 47 1 47 7 Riser Material, 46 8 3D...

Ngày tải lên: 07/07/2014, 07:20

... thinking ahead. 4. Select the two 45 ° walls, and mirror them around the horizontal refer- ence plane. You should now have four 45 ° walls, as shown in Figure 2 .44 . 5. You can now delete the vertical ... 2 .42 Adding the 45 ° wall ey e ba ll i n g W i t h aC C u r a C y You may notice when you are using temporary dimensions that the incre- ment always seems to “snap” to even increment...

Ngày tải lên: 07/07/2014, 07:20

... place an Interior - 6 1/8″ Partition (2-hr) wall as shown. This is the wall you will place the opening into. Placing Doors and Windows 87 3. As you know, in Revit Architecture anything that ... Model 84 FIGURE 2.65 Adding a door 4. Move your cursor over to the south wall near the elevator shaft, as shown in Figure 2.66. Notice that if your cursor is not within a wall, you get...

Ngày tải lên: 07/07/2014, 07:20

... opening. Also, dimension the floor plan as shown in Figure 5 .44 and Figure 5 .45 . FIGURE 5 .44 The dimensional layout for the north part of the west wing ... Dimensioning and Annotating 2 24 3. Revit will now give you a warning, as shown in Figure 5.32. You must then choose whether or not to unconstrain the elements. FIGURE 5.32 A Revit warning pertaining ... simply cannot type a...

Ngày tải lên: 07/07/2014, 08:20

... folder. 4. Select the following families: Base Cabinet-2 Bin.rfa  Base Cabinet-Double Door & 2 Drawer.rfa  Base Cabinet-Double Door Sink Unit.rfa  Base Cabinet-Filler.rfa  Base Cabinet-Single ... Cabinet-Double-Door-Wall 36 ″. 3. Place the wall cabinet in the model, as shown in Figure 9. 64. (Don’t worry too much about aligning it to the cabinet below. We will align it in ele...

Ngày tải lên: 07/07/2014, 08:20

... Adding Ramps 49 9 14. Set Width to 5’–0” (see Figure 10. 84) . 15. On the Draw panel, click the Run button. FIGURE 10.83 Modifying the Type Properties FIGURE 10. 84 Setting the properties Chapter ... If you take anything away from this chap- ter, take away the knowledge that stairs are not going to come easy, but you can create any staircase if you know you will need to create families....

Ngày tải lên: 07/07/2014, 08:20

... 16 .43 Adding the 3D mass 8. On the Quick Access bar, click the Default 3D View button. 9. Zoom in on the perimeter you have sketched and select it, as shown in Figure 16 .44 . FIGURE 16 .44 The ... & Site tab, click the In-Place Mass button, as shown in Figure 16 .41 . Adding a Wall to a Massing Object 759 FIGURE 16 .41 Click the In-Place Mass button. FIGURE 16 .42 Starting the mass...

Ngày tải lên: 07/07/2014, 08:20

... chapter, go to the book’s web page at www.sybex.com/go /revit2 011ner. From there you can browse to Chapter 17, and find the file called NER- 34. rvt. 1. Open the Cove Sweep file (if you have closed ... button on the Opening panel (see Figure 17. 14) . 8. By clicking Edit Sketch, you are now in Sketch Mode. On the Draw panel, click the Start-End-Radius Arc button, as shown in Figure 17.1...

Ngày tải lên: 07/07/2014, 08:20

... be a nice-to-know subject. For most of you, this is a need-to-know subject. Taking the plunge into Revit means that you may be tak- ing that plunge alone. Just because you are using Revit, that ... client is not standardized on the AIA format. Are You Experienced? Now You Can… import a Revit Structure model copy and monitor the Revit model run interference checking on a linked Re...

Ngày tải lên: 07/07/2014, 08:20