Autodesk Revit Architecture 2011 No Experience Required - part 3 ppsx

... open Revit Architecture, click the icon on your desktop (see Figure 1.1), or choose Start ➢ All Programs ➢ Autodesk ➢ Autodesk Revit Architecture 2011 ➢ Autodesk Revit Architecture 2011 (see ... relinquish. Introduction xxii Who Should Read This Book Autodesk ® Revit ® Architecture 2011: No Experience Required. Does that mean if you have used Revit yo...

Ngày tải lên: 07/07/2014, 07:20

... Since we do not have floors, Revit does not know where to stop. If you happen to place an elevation without floors, and then you put them in later, Revit will not make the adjust- ment. You still ... square to 1/2” circle (see Figure 3. 83) . 3. In the Type Parameters, under Graphics, change the Elevation Mark to Elevation Mark Circle - Upgrade : 1/2”. FIGURE 3. 83 Modifying the...

Ngày tải lên: 07/07/2014, 08:20

... 6.29. Building a Floor by Layers 2 63 FIGURE 6.29 Clicking the Copy To Clipboard button 3. Go to the default 3D view, as shown in Figure 6 .30 . 4. From the Paste fly-out on the Clipboard panel, click ... with. If you did not complete the previous chapter, go to the book’s web page at www.sybex.com/go/ revit2 011ner. From there you can browse to Chapter 6 and find the file called NER-20.r...

Ngày tải lên: 07/07/2014, 08:20

... wall no lon- ger sticks up past the roof. 4. Perform steps 1 through 3 for each corridor wall. When you are fin- ished, your corridor should be spanking nice, like Figure 7 .33 . FIGURE 7 .32 Attaching ... Footprint 31 3 FIGURE 7 .36 Setting the view range for the plan region 6. In the View Range dialog, set Top to Unlimited and Level 3 Cut Plane Offset to 35 ′–0″, as shown in Figu...

Ngày tải lên: 07/07/2014, 08:20

... how we can cre- ate our own. Notation and symbols are the basis for maintaining CAD standards. If you simply use the examples given to you by Revit, you will have a set of draw- ings that look ... there, you can double-click on the elevation marker pointing at the north leg of the kitchen. 2. Zoom in on the cabinets, as shown in Figure 11.86. Creating Custom Tags 5 63 Wh iC h on e do i...

Ngày tải lên: 07/07/2014, 08:20

... a 3D view. In this situation you want to use the actual Lines tool. Adding 2D and 3D Lines to the Model Just because we are drafting, that does not mean we can’t do it in a 3D function. Revit ... drag it into the model. Adding a Section to Another View You already know how to add a section marker in plan. What you may not know is how to tell Revit that you would rather specify the refer...

Ngày tải lên: 07/07/2014, 08:20

... make some minor modifications. 1. Open the view A401 - DETAILS (if it is not already). 2. Select the Corridor Entry Section view (the tall section to the right of the sheet). NOTE Notice that ... 23, so for now just click OK. 7. Zoom in on the detail and notice that the name has changed. Now that we have pretty much exhausted creating and manipulating sheets, it is time to explore a...

Ngày tải lên: 07/07/2014, 08:20

... Status: 100%  Project Name: NO EXPERIENCE REQUIRED  Project Number: 2009 034 2  NOTE Notice the NO EXPERIENCE REQUIRED text has already been entered. This is because you added it to the ... Figure 14 .34 . FIGURE 14 .33 Choosing the options to print the drawings Printing from Revit Architecture 691 In most cases, we don’t want the actual cover sheet to be an item in t...

Ngày tải lên: 07/07/2014, 08:20

... 4 ′–0″, as shown in Figure 17.27. 3. Draw another line to the right 1 3/ 8 ″. 4. Draw another line straight down 4 ′–0″. 5. Draw another line to the right 1 3/ 8 ″ (see Figure 17.27). 6. Click ... select Casing Profile-2.rfa. 8. Click Open. 9. In the menu on the Sweep panel, click the Profile drop-down and select Casing Profile 2:5 1/2″ × 3/ 16″ (notice the red dot is now replaced w...

Ngày tải lên: 07/07/2014, 08:20

... will still be oriented to Project North while the site plan is of a different orientation. Of course, now this mind- set makes the North Wing and the East Wing nomenclature irrelevant to the ... click the Edit button. 13. Choose Unlimited for both Primary Range: Bottom and View Depth Level. Orienting a Site 8 23 FIGURE 18 .31 The site rotated to true north FIGURE 18 .32 The Level 1 floor...

Ngày tải lên: 07/07/2014, 08:20