CNC program manual P2 pptx

... feedrate Example of program 33 20 40 60 70 90 110 140 Ø30 Ø40 Ø50 Ø60 Ø80 45° ∆u/2 ∆d e ∆w A (R) (R) (F) (F) C B A` (F) : Cutting feed (R) : Rapid traverse Program command TRAINING Examples of program Stock ... S80 M3 : G0 X47.0 Z1.0 T0101M8 : G74 R1.0 : G74 Z-10.0 Q3000 F0.1 : G0 U-5.0 : G74 X20.0 Z-10.0 P25 00 Q3000 F0.1 : G0 X200.0 Z200.0 T0100 : M30 : 10 Ø20 Ø50 10 Ø10 Ø30 Ø50...

Ngày tải lên: 06/07/2014, 11:20

... LabVIEW programming architectures E. About VI templates Lesson 1 Planning LabVIEW Applications LabVIEW Basics II Course Manual 1-16 ni.com More About Programming Architecture As with other programming ... the keyboard, sections of code, programming examples, and syntax examples. This font is also used for the proper names of disk drives, paths, directories, programs, subprograms, subroutine...

Ngày tải lên: 13/12/2013, 01:15

... the program is working and that employees are using respirators properly. - The employer shall establish and retain written information regarding medical exams, fit tests, and the respirator program. These ... use respiratory protective equipment. - An employee who participates in the medical monitoring program, but refuses any components of the examination, will be advised that the refu...

Ngày tải lên: 06/07/2014, 07:20

... X X P2 P2 P1 P1 K - K I - I P0 P0 Z Z I (X) K(Z) G02 G03 X Z N1234 G03 X Z (R ) 13 N1234 G02 X Z (R ) G03 G02 TRAINING 6 9 1 R 5 4 8 3 7 2 G41 G42 25 G41 G42 TRAINING G01 G02 PROGRAM G03 ... the end of main program. M30 : This is the same as M02 and it returns to the starting position of the programme when the memory and the tape are running. 2. M code should not be prog...

Ngày tải lên: 06/07/2014, 11:20

... to P2. N2 G2 X.5 Y.5 I.5 J0 Arc move to P3. N3 G1 X4.5 Feed to P4. N4 Y-3 Feed to P5. N5 X-5 Feed to P1. N6 M2 End Program. CNC Programming and Operations Manual P/N 70000508D - Manual ... notice. 3-5 25-July-03 Manual Mode Screen In Manual Mode, the CNC displays the Manual screen. The Manual screen is the basic operating screen and is displayed when the CNC...

Ngày tải lên: 06/07/2014, 10:21

... drive 7.370 4.422 2.948 5.896 Speed in km/h for 1000 rpm * 14.042 23.403 35.105 17.552 23-4 MANUAL GEARBOXES Differential output seal REMOVAL Remove the protective casing from under the en- gine. Drain ... fitting the differential seal B.Vi. 1058 Plug for fitting the differential seal 91755R 85965R 21-29 MANUAL GEARBOXES Gearbox (Removal - Refitting) 21 Remove the three bolts securi...

Ngày tải lên: 22/10/2012, 15:42

... ; End of program. N90 G93 I0 J0 ; Presetting the point X0 Y0 as the new Polar origin. N100 X100 Y100 N110 M30 ; End of program. R EF . 1010 8055 M Examples manual CNC  Examples manual ·M· ... to the previous position (G40 X _ Y_).  Examples manual ·M· Model 1. PROGRAM STRUCTURE Programming example R EF . 1010 ·8·  Examples manual ·M· Model 4. CANNED CYCLES Recta...

Ngày tải lên: 15/10/2013, 15:18

Ngày tải lên: 09/11/2013, 03:15

... not (usually) visible to the programmer § Segmentation is visible to the programmer § Usually different segments allocated to program and data § May be a number of program and data segments O/S ... de-fragmentation) Long Term Scheduling § Determines which programs are submitted for processing § i.e. controls the degree of multi-programming § Once submitted, a job becomes a process for the...

Ngày tải lên: 12/12/2013, 09:15