Advanced metal forming processes Subjects of interest docx
Advanced metal forming processes Subjects of interest docx
... Jan-Mar 2007 Advanced metal forming Advanced metal forming processes processes • Introduction/Objectives • Superplastic forming • Pressing and sintering • Isostatic pressing Subjects of interest Chapter ... costly. Superplastic forming Tapany Udomphol Suranaree University of Technology Jan-Mar 2007 • Advanced techniques for metal forming are listed below; Intro...
Ngày tải lên: 06/07/2014, 09:20
Forging Subjects of interest docx
... fluid Metal Tapany Udomphol Suranaree University of Technology Jan-Mar 2007 Example: Die set and forging steps for the manufacturing of an automobile engine connecting rod • Preforming of a round ... Udomphol Introduction Introduction • Forging is the working of metal into a useful shape by hammering or pressing. • The oldest of the metalworking arts (primitive blacksmith)....
Ngày tải lên: 06/07/2014, 09:20
Drawing of rods, wires and tubes Subjects of interest docx
... is composed of carbides of Ti, W, Ni, Mo, Ta, Hf. Tapany Udomphol Suranaree University of Technology Jan-Mar 2007 • Drawing operations involve pulling metal through a die by means of a tensile ... University of Technology Jan-Mar 2007 The effect of die angle on the total energy required to cause deformation U T U P α αα α * U f U r α αα α U Components of total energy of d...
Ngày tải lên: 06/07/2014, 09:20
Sheet-metal forming Subjects of interest doc
... Suranaree University of Technology Jan-Mar 2007 Hydroforming Stamp hydroforming machine setup with a fluid supplied from one side of the draw blank www.egr.msu.edu A drawing of hydroforming setup ... condition Tapany Udomphol Suranaree University of Technology Jan-Mar 2007 Classification of sheet metal forming (based on operations) Wiping down a flangeRoll forming of shee...
Ngày tải lên: 06/07/2014, 09:20
Magnesium and its alloys Subjects of interest ppsx
... those of Al alloys. Tapany Udomphol Suranaree University of Technology May-Aug 2007 Magnesium and its alloys Magnesium and its alloys Subjects of interest • Introduction/Objectives • Production of ... University of Technology May-Aug 2007 Objectives Objectives • This chapter provides fundamental knowledge of different methods of productions / heat treatments of magnesium...
Ngày tải lên: 06/07/2014, 09:20
Rolling of metals Subjects of interest pdf
... rolling Suranaree University of Technology Jan-Mar 2007 A variety of sections can be produced by roll forming process using a series of forming rollers in a continuous method to roll the metal sheet to a ... rolls and the metal is a part of a circle. 2) The coefficient of friction, µ µµ µ , is constant in theory, but in reality µ µµ µ varies along the arc of contact....
Ngày tải lên: 06/07/2014, 09:20
Extrusion Subjects of interest ppsx
... extrusion • Analysis of the extrusion process • Cold extrusion and cold -forming • Hydrostatic extrusion • Extrusion of tubing • Production of seamless pipe and tubing Chapter 4 Subjects of interest Tapany ... objects, soft metal, large numbers, good tolerances*. Tapany Udomphol Suranaree University of Technology Jan-Mar 2007 Classification of extrusion processes Classifi...
Ngày tải lên: 06/07/2014, 09:20
Machining of metals Subjects of interest pps
... and tool life • Grinding processes • Non traditional machining processes • Economics of machining Chapter 7 Subjects of interest Tapany Udomphol Suranaree University of Technology Jan-Mar 2007 vF vF energyTotal engergyShearing h ss = From ... affects machining of metals. • Mechanics of machining is introduced for the calculation of power used in metal machining operati...
Ngày tải lên: 06/07/2014, 09:20
Hardness Test Subjects of interest potx
... indentation (b) is the result of sinking in of the metal around the flat faces of the pyramid. This gives an overestimate of the diagonal length (observed in annealed metals). • The barrel-shaped ... metals, resulting from ridging or piling up of the metal around the faces of the indenter. Produce a low value of contact area giving too high value. Tapany Udomphol Surana...
Ngày tải lên: 06/07/2014, 09:20
