CCNA 1 and 2 Companion Guide, Revised (Cisco Networking Academy Program) part 90 docx

... [fragments] Example 20 -3 Extended ACL Statements access-list 11 4 permit tcp 17 2 .16 .6.0 0.0.0 .25 5 any eq telnet access-list 11 4 permit tcp 17 2 .16 .6.0 0.0.0 .25 5 any eq ftp access-list 11 4 permit tcp 17 2 .16 .6.0 ... marketing_group permit tcp any 17 1.69.0.0 0 .25 5 .25 5 .25 5 eq telnet deny tcp any any deny udp any 17 1.69.0.0 0 .25 5 .25 5 .25 5 lt 10 24 den...

Ngày tải lên: 04/07/2014, 18:20

... links Time Interval 10 Mbps 5 12 bit-times 51. 2 µsec 10 0 Mbps 5 12 bit-times 5 . 12 µsec 1 Gbps 4096 bit-times 4.096 µsec 10 Gbps Not applicable — 11 02. book Page 27 5 Tuesday, May 20 , 20 03 2: 53 PM Ethernet ... nanosecond 10 00 Mbps = 1 Gbps 1 nanosecond 10 ,000 Mbps = 10 Gbps .1 nanosecond 11 02. book Page 27 4 Tuesday, May 20 , 20 03 2: 53 PM Ethernet Operatio...

Ngày tải lên: 04/07/2014, 18:20

... 300m 10 GBASE-LX4 13 10 nm 50 µm MMF 400 MHz/km 2m to 24 0m 10 GBASE-LX4 13 10 nm 50 µm MMF 500 MHz/km 2m to 300m 10 GBASE-LX4 13 10 nm 10 µm SMF — 2 km to 10 km 10 GBASE-S 850 nm 62. 5 µm MMF 16 0 MHz/km 2m ... 6 -27 . Figure 6 -27 Building an Address Table AC B 1 2 3 4 10 Mbps 10 Mbps Interface Stations 12 3 4 Data from A to B AC B 1 2 3 4 10 Mbps 10 Mbps Interfa...

Ngày tải lên: 04/07/2014, 18:20

... equivalents: 11 000000 .10 1 010 00.000000 01. 000 010 00 11 000000 .10 1 010 00.000000 01. 000 010 01 Looking at the binaries, it is almost impossible to see that they are consecutive numbers. 11 02. book Page 388 ... address 19 2 .16 8 .1. 8 is 11 000000 .10 1 010 00.000000 01. 000 010 00 in binary notation. It is plain to see that it is easier for humans to understand dotted-decim...

Ngày tải lên: 04/07/2014, 18:20

... networks—networks 2 and 3.) Figure 8 - 12 Network Addresses 1. 1 3 .1 2 .1 Network 1 2 3 1 2 3 1 1 Host 1. 2 1. 3 11 02. book Page 438 Tuesday, May 20 , 20 03 2: 53 PM Routed, Routable, and Routing Protocols ... the Internet. As shown in Figure 8 -2, all 25 4 addresses in the sequence of 19 2 .16 8 .10 .1 to 19 2 .16 8 .10 .25 4 can be represented by th...

Ngày tải lên: 04/07/2014, 18:20

... network and some other network. Figure 10 -13 identifies the border routers in the sample network that was used in Figure 10 -11 and Figure 10 - 12 . Figure 10 -13 Border Routers Router Router Router Router Router Router Router Router Router Router Exterior Routers Internetwork Private ... standards describe? A. Data link and network B. Data link and presentation C. Physical and...

Ngày tải lên: 04/07/2014, 18:20

... Protocol Ethernet0 19 8 .13 3. 21 9 .1 YES NVRAM up down Serial0 unassigned YES NVRAM administratively down down Serial1 unassigned YES NVRAM administratively down down Example 11 -1 setup Command (Continued) 11 02. book ... dialog when the router is rebooted. Figure 11 -1 shows the startup sequence. 11 02. book Page 554 Tuesday, May 20 , 20 03 2: 53 PM 550 Chapter 10 : WANs...

Ngày tải lên: 04/07/2014, 18:20

... software installations and upgrades Table 12 -7 Host Table Router Name Router Type E0 E1 S0 Tokyo 26 01 20 5.7.5 .1 1 92. 5.5 .1 2 01. 100 .11 .1 Paris 26 21 20 5.7.5 .2 204 .20 4.7 .2 Example 12 - 12 Host Table Configuration Router(config)# ... Configuration Router(config)# ip host Auckland 17 2 .16 . 32 .1 Router(config)# ip host Beirut 19 2 .16 8.53 .1 Router(config...

Ngày tải lên: 04/07/2014, 18:20

... closer to 60 to 70m (19 6.9 to 22 9.7 ft.) than 10 0m ( 328 .1 ft.); 50m (16 4 ft.) commonly is used as a work- area radius for design purposes. appen_a.fm Page 888 Tuesday, May 20 , 20 03 4:54 PM ... cabling business ■ Case study Completing this material and the associated labs in the Cisco Networking Academy Program CCNA 1 and 2 Lab Companion, Third Edition, will...

Ngày tải lên: 04/07/2014, 18:20

... electrical wire. Figure A -23 Stud Sensor appen_a.fm Page 918 Tuesday, May 20 , 20 03 4:54 PM Tools of the Trade 917 Figure A -20 Panduit Multipair Impact Tool Figure A- 21 Panduit Impact Tool Diagnostic ... Page 911 Tuesday, May 20 , 20 03 4:54 PM Tools of the Trade 915 ■ Diagnostic tools ■ Installation support tools Stripping and Cutting Tools Stripping tools are used to cut the ca...

Ngày tải lên: 04/07/2014, 18:20