DISCRETE-SIGNAL ANALYSIS AND DESIGN- P25 pot
DISCRETE-SIGNAL ANALYSIS AND DESIGN- P25 pot
... completely related one way or the other, and 0 means that
x(n)andy(n) are completely unrelated (independent). The basic equation
106 DISCRETE-SIGNAL ANALYSIS AND DESIGN
Equation (6-12) is assumed, ... 110 DISCRETE-SIGNAL ANALYSIS AND DESIGN
removes the time average n
x
and the result is a good approximation
to the ac value expected. ... each other in increments of τ.
108 D...
DISCRETE-SIGNAL ANALYSIS AND DESIGN- P12 potx
... Engineer’s Handbook, McGraw-Hill, New York.
Zwillinger, D., ed., 1996, CRC Standard Mathematical Tables and Formulae 30th
ed., CRC Press, Boca Raton, FL.
44 DISCRETE-SIGNAL ANALYSIS AND DESIGN
0123456789101112131415
−350
−250
−200
−150
−100
−50
0
k
(a)
(b)
10
−15
10
−6
10
−3
dB
0 ... example with k =15.0, and the discrete spectrum
Discrete-Signal Analysis and Design, By Willia...
DISCRETE-SIGNAL ANALYSIS AND DESIGN- P13 potx
... 48 DISCRETE-SIGNAL ANALYSIS AND DESIGN
sine wave with an added dc bias. The DFT (see Fig. 3-1f) shows the
correct ... the frequency
counter problem. However, phase noise (related to frequency jitter) and
other random or pseudo random problems can often be improved by using
statistical methods such as record averaging, ... integer-valued frequencies. Two
values of percentage frequency...
DISCRETE-SIGNAL ANALYSIS AND DESIGN- P29 pot
... also
smoothed two times and the comparison of VN (k )andVN
2
(k)is
seen in the graphs of parts (e) and (f).
(f) Note that in parts (e) and (f) the upper level of the phase noise plot
VT (k)andVT
2
(k)is>53 ... reject interference to and from closely adjacent signals
130 DISCRETE-SIGNAL ANALYSIS AND DESIGN
(b) Execute the DFT to get X (k), the two-sided, positive-frequency Þrs...
DISCRETE-SIGNAL ANALYSIS AND DESIGN- P35 potx
... time
for each X (s) [Dorf and Bishop, 2004, Sec. 3], but we want to use the dis-
crete derivative of Eq. (A-2) as an alternative for discrete-signal analysis
and design [Dorf and Bishop, 2004, Sec. ... circuit analysis conÞrms these facts for this example. R, L,
and C are constant values, but they can easily be time-varying and/ or
nonlinear functions of voltage and current....
QUASILINEAR CONTROL: Performance Analysis and Design of Feedback Systems with Nonlinear Sensors and Actuators pot
... system.
the actuator and sensor, F
d
(s) and F
r
(s) are coloring filters with 3dB bandwidths
d
and
r
, respectively, w
r
, w
d
are independent standard Gaussian white noise
processes, and the scalars ... P(s) and C(s) represent the plant and controller, respectively, and the nonlinear
functions f (·) and g(·) describe, respectively, the actuator and sensor. The signa...
SAP2000® Linear and Nonlinear Static and Dynamic Analysis and Design of Three-Dimensional Structures
... Save command, or the Save
button, to
save your model.
Step 8 Run the Analysis
In this Step, the analysis will be run.
A. Click the Analyze menu > Run Analysis command or the Run
Analysis ... EFFORT AND EXPENSE HAVE GONE INTO THE
DEVELOPMENT AND DOCUMENTATION OF SAP2000. THE PROGRAM HAS
BEEN THOROUGHLY TESTED AND USED. IN USING THE PROGRAM,
HOWEVER, THE USER ACCEPTS...
SAP2000 Integrated Finite Elements Analysis and Design of Structures
... the frame elements and joints.
• Click and hold the left mouse button.
• While holding, move the pointer below and to the right of the frame elements and joints.
A “rubber-band” window will show ... then run the linear static and
dynamic analysis by clicking Run on the Analyze menu. Next select Run Static Pushover from
the Analysis menu to perform the pushover analysis. The res...
Từ khóa: