...
network 192.168.192.0
network 192.168.193.0
network 192.168.194.0
network 192.168.195.0
no auto-summary
router bgp 100
no synchronization ... default
dial-peer cor custom
line con 0
logging synchronous
line aux 0
line vty 0 4
password cisco
login
end
Kết quả là trên các router thuộc AS 200 thì tất cả các
route đều nhận được bình ... damped, h history, * valid,
> b...
... trong multi-access
network một DR được bầu ra trong multi-access network. DR có những nhiêm vụ
sau:
Đại diện cho multi-access network và gắn bó với phần còn lại internetwork.
Để quản ... (link) và trạng thái của link. Các link này có thể là
stub network, tới OSPF router khác, tới network trong cùng một area, tới external
network. Do có rất nhiều loại link state information ch...
... Các tài nguyên này thường nằm trong nhìều
VLAN khác nhau.
II. TRIỂN KHAI VLAN:
Chia VLAN trên Cisco Catalyst Switch có 2 bước:
1. Tạo VLAN
2. Gán SW port vào VLAN có 2 kiểu:
- Static: áp
... thấy đường đến mạng đích đó trong routing table,
router sẽ discard packet đó và gửi một gói ICMP network unreachable về
host nguồn đã gửi packet.
N
ếu tìm thấy trong routing table tuyến đường ... mạng đích
không tìm thấy trong routing table thì router sẽ drop packet và g
ửi một bản
tin ICMP network unreachable tới nơi gửi packet đó.
Xét dòng thông tin sau:
R 175.21.0.0/16 [120/...
... đã
nêu ở trên .
pixfirewall>en
password:
pixfirewall#enable password cisco
=>đặt password ở mode enable là cisco .
pixfirewall# write memory
Building configuration
Cryptochecksum: ... show version để kiểm
tra pix
đang chạy OS nào :
pixfirewall> sh version
Cisco PIX Firewall Version 6.3(1)
Cisco PIX Device Manager Version 3.0(1)
Compiled on Wed 19-Mar-03 11:49 by...
... drop packet
hoặc reset lại kết nối. 53 signature làmột tập con của các signature
được hỗ trợ bởi Cisco Intrusion Detection System (CIDS)
PIX Firewall có thể phát hiện hai loại signature khác nhau:
... của IGRP, vài network có thể làm default route mặc dù chỉ một default-route là
được dùng.
Nếu một router không có một network kết nối trực tiếp nhưng có một route ... candidate default-route. Để cấu hình một default-
route, dùng lệnh sau:
Router(config)#ip default -network network-number
lệnh này sẽ tạo ra một default route được gửi trong các update. Nó sẽ không ... đánh dấu như một...
... you can configure PRIs back-to-back
between routers: configure one side to be network side (isdn protocol-emulate
network) and the other to be user side (default; isdn protocol-emulate user). ... posting had alluded, we have SOME support for network- side BRI
- but this is only on certain VIC cards due to hardware restrictions -
http://www .cisco. com/univercd/cc/td/doc/product/softwar...