... Interfaces and Protocols The previous section introduced GSM network architecture, and this section introduces the SS7/C7 protocols that are used. It also discusses interfaces, because different protocols ... interfaces. The SS7/C7 protocols MTP, SCCP, TUP, ISUP are protocols that were used before digital wireless networks were available. The final part of this section introduces...
Ngày tải lên: 02/07/2014, 09:20
... Allocation of Signaling Terminals and Links The SS7 standards provide specifications for the automatic allocation of both signaling terminals and signaling links. The automatic allocation of signaling ... recovering from SS7 outages. The newly in-service or recovering node deals with heavy SS7 management traffic and might have limited SS7 resources available initially. The T...
Ngày tải lên: 02/07/2014, 08:21
Signaling System No.7 Protocol Architecture And Sevices part 23 ppsx
... called party exist in many countries; however, terminal p ortability for the calling party is not supported as often. ANSI networks do not support terminal portability for the calling party. ... group. The provisioned signaling type for the selected trunk group determines whether ISUP signaling or some other signaling, such as Multifrequency (MF), is used. When the signaling type...
Ngày tải lên: 02/07/2014, 08:21
Signaling System No.7 Protocol Architecture And Sevices part 26 ppsx
... Application Part (CAP), MAP, INAP, and AIN. Table 9-1 shows the connectionless service protocol classes and features. Table 9-1. Connectionless Service Protocol Classes Protocol Class and Name ... Control Part (SCCP) is defined in ITU-T Recommendations Q .71 1-Q .71 6 [58 –63] and for North American markets in ANSI T1.112 [2 ]. SCCP sits on top of Message Transfer...
Ngày tải lên: 02/07/2014, 08:21
Signaling System No.7 Protocol Architecture And Sevices part 55 ppsx
... alternative to H.323. SIP is a signaling protocol that handles the setup, modification and teardown of multimedia sessions. It was developed in the IETF as a signaling protocol for establishing ... Reliable UDP (RUDP) and Session Manager (SM) protocols. A generic backhaul protocol layer is used to provide adaptation between MTP Level 2 and MTP Level 3. Figure 14-28 shows...
Ngày tải lên: 02/07/2014, 09:20
Signaling System No.7 Protocol Architecture And Sevices part 61 ppsx
... and that it is used for both validation and compatibility testing purposes. It consists of two parts: p art (a) and part (b). Part (b) is the same test repeated in the reverse direction. Part ... should not provide a positive acknowledgment until timer T7 is on the threshold of timing out. The acknowledgment that is sent on the verge of expiration of T7 should be a positive ac...
Ngày tải lên: 02/07/2014, 09:20
Signaling System No.7 Protocol Architecture And Sevices part 1 ppsx
... p rovide the novice reader with a better understanding of the book's main topic: Signaling System No. 7. Today, Signaling System No. 7 is the most advanced and widely used signaling system for ... Channel Signaling (CCS) method of signaling and its operational modes • The limitations of CAS and CCS Signaling System No. 7, known more commonly in North A...
Ngày tải lên: 02/07/2014, 09:20
Signaling System No.7 Protocol Architecture And Sevices part 2 ppt
... Associated Signaling (CAS) techniques and systems. However, for the past two decades, it has been replaced with Common Channel Signaling (CCS) systems. Apart from a rare trace of Signaling System No. ... (SS6) signaling, System No. 7 (SS7) is almost the exclusive CSS system; thus, CCS can almost be taken to refer exclusively to the use of SS7. The remaining sections of t...
Ngày tải lên: 02/07/2014, 08:21
Signaling System No.7 Protocol Architecture And Sevices part 3 pps
... therefore, signaling is sent above the 3400 Hz (and below 4000 Hz). This is known as out-of-band signaling and is used in R2 for supervisory signaling. Unlike with in-band signaling, no contention ... implemented using the following related systems: • Bell Systems MF, R2, R1, and C5. • Single-frequency (SF) in-band and out-of-band signaling • Robbed bit signaling The...
Ngày tải lên: 02/07/2014, 08:21
Signaling System No.7 Protocol Architecture And Sevices part 4 potx
... digital CAS signaling. The only CCS systems that have been implemented to date are Signaling Systems N o. 6 and No. 7 (SS6 and SS7). The ITU for the international network originally standardized ... telecommunications standards and for Internet standards. These two worlds are now intersecting, creating the need for additional standards to address new architectures, protocols,...
Ngày tải lên: 02/07/2014, 08:21