SolidWorks 2010- P20 ppsx

... aspects of SolidWorks that should allow you to be able to take and pass the Certified SolidWorks Associate (CSWA) exam and be well on the way to taking and pass- ing the Certified SolidWorks Professional ... database of material appearances, most of which can also be found in SolidWorks. In fact, an appearance added to a component in SolidWorks will carry over into PhotoView 360, w...

Ngày tải lên: 01/07/2014, 22:20

... browse to the location where your SolidWorks templates are located. In most cases, the location for templates in SolidWorks 2010 is C:\ProgramData \SolidWorks\ SolidWorks2010\ templates . NOte ... drawing in SolidWorks. In fact, it is the same. The only difference is that you cannot make any changes to the drawing. 6. The user interface for eDrawings also a lot simpler from that of...

Ngày tải lên: 01/07/2014, 22:20

... information, in SolidWorks see Help, About. Other portions of SolidWorks 2009 are licensed from DS SolidWorks licensors. All Rights Reserved. Pre-Release DRAFT Do not copy or distribute Lesson 1 SolidWorks ... Tips On/Off Pre-Release DRAFT Do not copy or distribute SolidWorks 2010 Lesson 1 SolidWorks Basics and the User Interface 13 The SolidWorks User Interface The SolidWork...

Ngày tải lên: 06/01/2014, 22:28

... 13.2 Aufbereiten von eDrawings-Dateien aus SolidWorks 244 14 FE Analyse mit SolidWorks SimulationXpress 251  14.1 SolidWorks SimulationXpress und SolidWorks Simulation 251 14.2 Durchführen ... Fragen rund um SolidWorks Hilfe erhalten. Zum einen hat SolidWorks für den Ausbildungsbereich ein Forum eingerichtet, an dem Sie als registrierter Anwender teilhaben können (www.fo...

Ngày tải lên: 08/01/2014, 16:28

... time launching SolidWorks for the first time, becoming familiar with the SolidWorks interface, and working with the CommandManager. Start SolidWorks Before installing and running SolidWorks for ... with SolidWorks 1 Start SolidWorks 2 SolidWorks License Agreement 3 Help and Workflow Customization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Navigat...

Ngày tải lên: 27/06/2014, 02:20

Ngày tải lên: 29/06/2014, 14:20

... with SolidWorks 1 Start SolidWorks 2 SolidWorks License Agreement 3 Help and Workflow Customization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Navigate the SolidWorks ... team and is very well known in the SolidWorks community as the SolidWorks Geek, which is the name of his blog ( www.TheSWGeek.com ). Gabi Jack is a Certified SolidWorks Professio...

Ngày tải lên: 01/07/2014, 22:20

... computer is able to support SolidWorks and it is installed onto your system, you can launch it by selecting Start ➢ Programs ➢ SolidWorks 2010 ➢ SolidWorks 2010 SPX.X ➢ SolidWorks 2010. NOte ... time launching SolidWorks for the first time, becoming familiar with the SolidWorks interface, and working with the CommandManager. Start SolidWorks Before installing and running...

Ngày tải lên: 01/07/2014, 22:20

... dot (.) in the filename. The three document types are as follows: SolidWorks part file *.sldprt SolidWorks assembly file *.sldasm SolidWorks drawing file *.slddrw In this chapter, we’ll demonstrate ... becoming a SolidWorks master. Use Default Shortcuts Out of the box, SolidWorks comes with over 40 pre-programmed shortcut keys that in most cases will be more than enough for your daily...

Ngày tải lên: 01/07/2014, 22:20

... New button located on the menu bar at the top of the SolidWorks window. 2. The New SolidWorks Documents window, by default, offers three SolidWorks document types: part, assembly, and drawing. ... Creating Your First Part 82 N ow that you have spent some time going over the user interface of SolidWorks and have explored the different document types, you can begin creating your first...

Ngày tải lên: 01/07/2014, 22:20