SolidWorks 2010- P1 ppt

... information. . CAUTION : Detailed descriptions of standard work- shop procedures, safety principles and service op- erations are not included. Please note that this manu- al does contain warnings and cautions against ... not could GM DAEWOO in- vestigate all such ways. Anyone using service proce- dures or tools, whether or not recommended by GM DAEWOO, must satisfy himself thoroughly that nei...

Ngày tải lên: 30/10/2012, 08:47

Ngày tải lên: 07/11/2013, 16:15

... sắm 10. 10. Quản lí chi phí Quản lí chi phí 11. 11. Quản lí chất lượng Quản lí chất lượng 12. 12. Quản lí rủi ro dự án Quản lí rủi ro Quản lí dự án Quản lí dự án Công nghệ thông tin Công nghệ thông tin 1 ... thống Làm tài liệu Người quản lí dự án Liên hệ khách hàng Ước lượng và lập lịch Liên hệ cấp quản lí Lập kế hoạch dự án Theo dõi...

Ngày tải lên: 12/12/2013, 09:16

... with SolidWorks 1 Start SolidWorks 2 SolidWorks License Agreement 3 Help and Workflow Customization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Navigate the SolidWorks ... team and is very well known in the SolidWorks community as the SolidWorks Geek, which is the name of his blog ( www.TheSWGeek.com ). Gabi Jack is a Certified SolidWorks Professio...

Ngày tải lên: 01/07/2014, 22:20

... dot (.) in the filename. The three document types are as follows: SolidWorks part file *.sldprt SolidWorks assembly file *.sldasm SolidWorks drawing file *.slddrw In this chapter, we’ll demonstrate ... becoming a SolidWorks master. Use Default Shortcuts Out of the box, SolidWorks comes with over 40 pre-programmed shortcut keys that in most cases will be more than enough for your daily...

Ngày tải lên: 01/07/2014, 22:20

... accurate as possible. At a later date when you become more comfortable with modeling parts in SolidWorks, it would be great practice to design these components to finish your assembly. Here’s ... avoided this issue; the first is using a smaller radius for the fillet. If the fillet was smaller, SolidWorks wouldn’t have needed to change the geometry of the fillet to move around the boss. The...

Ngày tải lên: 01/07/2014, 22:20

... Prior to SolidWorks 2010, adding a center mark to a dimension circle or arc would result in a single solid line because the center mark would lie directly on top of the extension line. In SolidWorks ... creating a detached drawing. A detached drawing allows you to share the actual SolidWorks drawing with other SolidWorks users without the need for the model data. The advantage to...

Ngày tải lên: 01/07/2014, 22:20

... washer cover will be present only in the Open Documents field if the model is currently opened in SolidWorks. If you closed the model for the washer cover after creating it, you will need to select ... 6.21 Inserting washer cover into assembly There may be times in the future while you are using SolidWorks that you will need to insert multiple components into your assembly. Instead of se...

Ngày tải lên: 01/07/2014, 22:20

... assembly using the following steps: 1. Click New in the menu bar, and select Assembly in the New SolidWorks Document window. Click OK to create a new assembly model. 2. Click Browse in the Begin ... accept its default location. Since this is the first component being inserted into the assembly, SolidWorks can automati- cally specify the location of the part. Clicking the green check ma...

Ngày tải lên: 01/07/2014, 22:20

... outside source without including the actual 3D geometry. This allows other SolidWorks users to open a drawing in the native SolidWorks format without the model or assembly. Doing it this way saves ... The viewer can open and view SolidWorks native file formats and eDrawings formats. The advantage of using eDrawings is that you can send models and drawings to non -SolidWorks users. W...

Ngày tải lên: 01/07/2014, 22:20

... 685 Utilización de coordenadas y de sistemas de coordenadas (SCP) . . . . 685 Introducción a la especificación de coordenadas . . . . . . . . . 685 Introducción de coordenadas bidimensionales . ... aplicación y en la cinta de opciones. El campo de búsqueda se muestra en la parte superior del menú de la aplicación. Entre los resultados de búsqueda pueden figurar comandos...

Ngày tải lên: 02/07/2014, 06:20

... eBook version ISBN 97 8-1 -4 30 2-2 77 8-6 9 781430 227786 5 3 4 9 9 THE EXPERT’S VOICE ®  IN LINUX Smart Home Automation with Linux Steven Goodwin Learn how to control your home from your PC Steven ... or retrieval system, without the prior written permission of the copyright owner and the publisher. ISBN-13 (pbk): 97 8-1 -4 30 2-2 77 8-6 ISBN-13 (electronic):...

Ngày tải lên: 03/07/2014, 20:20

... tế với các nước trong khu vực và trên thế giới. Kết cấu hạ tầng giao thông vận tải phát triển sẽ là chất xúc tác tích cực cho mọi hoạt động trong nền kinh tế phát triển nhanh. Vì vậy đầu tư phát ... là phải xây dựng hệ thống kết cấu hạ tầng kinh t - xã hội hoàn chỉnh và đồng bộ. Trong đó kết cấu hạ tầng giao thông là bản lề quan trọng...

Ngày tải lên: 22/07/2014, 08:21

... 10 11 Terminating ribs 10 11 Using thin features 10 13 Using Draft 10 14 Neutral Plane draft 10 14 Parting Line draft 10 15 Step draft 10 15 Some draft limitations 10 16 What to do when draft fails 10 17 DraftXpert ... feature 910 Fixed Face 910 Jog Offset 911 Fix projected length 911 Jog Position 911 Jog Angle 911 Sketched Bend feature 911 Closed Corner feature 912 Faces t...

Ngày tải lên: 09/08/2014, 12:21

... selected sketch element. Chapter 21: Working with Drawing Views 70 5 FIGURE 21.16 Setting the depth of the Broken-out Section View FIGURE 21. 17 Editing the Broken-out Section View Break View Break ... Administration and specific recommendations for templates and formats, please refer to the SolidWorks Administration Bible (Wiley, 2009). n Summary Getting your templates and formats...

Ngày tải lên: 09/08/2014, 12:21