The Fundamentals of Graphic Design- P1 doc

... No:01077 Title :The fundamentals og Graphic Design 1ST Proof Page:18 18 The Fundamentals of Graphic Design Graphic design as a discipline Office size and work relationships An office contains ... Title :The fundamentals og Graphic Design 1ST Proof Page:1 The Fundamentals of Graphic Design Gavin Ambrose + Paul Harris 001-023 01077.qxd 8/6/08 4:02 PM Page 1 Job No:...

Ngày tải lên: 27/06/2014, 02:20

... decision is made, the rest of the design features follow. For example, Version 2 ME, IIT Kharagpur once we decide the engine capacity, the shape and size, then the subsequent course of the design ... Instructional Objectives At the end of this lesson, the students should have the knowledge of • Basic concept of design in general. • Concept of machine d...

Ngày tải lên: 17/12/2013, 11:15

... MathWorks, Inc. The software described in this document is furnished under a license agreement. The software may be used or copied only under the terms of the license agreement. No part of this manual ... DFARS Part 252.227-7014. The terms and conditions of The MathWorks, Inc. Software License Agreement shall pertain to the government’s use and disclosure of the Pro...

Ngày tải lên: 22/12/2013, 20:16

... compressive stress of π 2 4F d and a bending stress of My I are produced. Here d is the diameter of the circular bar, I the second moment of area and the moment is PL 2 where the beam length ... X-X, Q the first moment of area, I the moment of inertia, t the width at which transverse shear is calculated, J the polar moment of inertia and r the radiu...

Ngày tải lên: 25/12/2013, 23:18

... normal stress is the same throughout the length of the rod but the bearing stress is largest at the welded end. Now among the four corner elements on the rod, the element A is mostly loaded as ... or equal to the limiting material strength then the designed component may be considered to be safe and an indication about the size of the component is obtained. The...

Ngày tải lên: 25/12/2013, 23:18

... figure-3.2.3.1 ‘a’ is the radius of the hole and at r=b, b>>a the stresses are not affected by the presence of the hole. Version 2 ME, IIT Kharagpur 3.2.2 Methods of reducing stress ... Kharagpur the effect due to the 2 nd component can be analyzed following the Stress-function approach. Using a stress function of the form ( ) Rrcos2 φ =θ th...

Ngày tải lên: 25/12/2013, 23:18

... rotating-bending load. The dimensions are shown in the figure and the bending moment is 30 Nm. The shaft has a ground finish and an ultimate tensile strength of 1000 MPa. Determine the life of the shaft. ... Q.2: A portion of a connecting link made of steel is shown in figure-3.4.4.3 . The tensile axial force F fluctuates between 15 KN to 60 KN. Find the factor...

Ngày tải lên: 25/12/2013, 23:18

... only then 12 α <φ +φ for self locking. Clearances between the cotter and slots in the rod end and socket allows the driven cotter to draw together the two parts of the joint until the socket ... when this is driven in, the rod is forced into the socket. However, if the taper is provided on both the edges it must be less than the sum of the friction angles fo...

Ngày tải lên: 25/12/2013, 23:18

... required, and the line of action of the force. Mathematically, Moment of a force = F × l where F = Force acting on the body, and l = Perpendicular distance of the point and the line of action of the force ... atom. 1.121.12 1.121.12 1.12 PrPr PrPr Pr esentaesenta esentaesenta esenta tion of Units and their tion of Units and their tion of Units and their tion of...

Ngày tải lên: 26/12/2013, 00:17

... = 30% of the yield strength but not over 18% of the ultimate strength in tension for shafts without keyways. These values are to be reduced by 25% for the presence of keyways in the shaft. ... = 30% of the yield strength but not over 18% of the ultimate strength in tension for shafts without keyways. These values are to be reduced by 25% for the presence of k...

Ngày tải lên: 23/01/2014, 04:20