Fundamentals of Spread Spectrum Modulation docx

Fundamentals of Spread Spectrum Modulation docx

Fundamentals of Spread Spectrum Modulation docx

... descriptions of two generic spread spectrum modulation techniques—QPSK spreading and frequency-hop spread spectrum. book Mobk087 August 3, 2007 13:15 FUNDAMENTALS OF SPREAD SPECTRUM MODULATION ... 13:19 Fundamentals of Spread Spectrum Modulation i MOBK087-FM MOBKXXX-Sample.cls August 3, 2007 13:19 v Contents FundamentalsofSpreadSpectrumModulation 1 1 Introducti...

Ngày tải lên: 27/06/2014, 09:20

86 280 0
Tài liệu Fundamentals of Machine Design P7 docx

Tài liệu Fundamentals of Machine Design P7 docx

... torque of 5 KN-m. The material has a yield point of 350 MPa. Find the required diameter using (a) Maximum shear stress theory (b) Maximum distortion energy theory Take a factor of safety of 2.5. ... Summary of this Lesson Different types of loading and criterion for design of machine parts subjected to static loading based on different failure theories have been demonstra...

Ngày tải lên: 25/12/2013, 23:18

21 473 0
Tài liệu Fundamentals of Machine Design P10 docx

Tài liệu Fundamentals of Machine Design P10 docx

... However, in the presence of notches and cracks determination of total strain is difficult. 3.4.1.2F- Plots of strain amplitude vs number of stress reversals for failure. ... schematic plot of reversed stress against number of cycles to fail. 3.4.3 Fatigue strength formulations Fatigue strength experiments have been carried out over a wide range of...

Ngày tải lên: 25/12/2013, 23:18

14 504 0
Tài liệu PRINCIPLES OF SPREAD-SPECTRUM COMMUNICATION SYSTEMS ppt

Tài liệu PRINCIPLES OF SPREAD-SPECTRUM COMMUNICATION SYSTEMS ppt

... summations to we obtain The information-weight spectrum or distribution is defined as In terms of this distribution, (1-110) becomes PRINCIPLES OF SPREAD- SPECTRUM COMMUNICATION SYSTEMS 32 CHAPTER ... number of sequences that can be obtained by changing any of the nonzero symbols to zeros is where if For a specified value of it is necessary that to ensure a sequence of weight...

Ngày tải lên: 20/01/2014, 06:20

457 421 0
Tài liệu Fundamentals of Machine Design P22 docx

Tài liệu Fundamentals of Machine Design P22 docx

... (8.1.1) Where, M : Bending moment at the point of interest d o : Outer diameter of the shaft k : Ratio of inner to outer diameters of the shaft ( k = 0 for a solid shaft because ... is a mixture of various elements with the parent steel to improve certain physical properties. To retain the total advantage of alloying materials one requires heat treatment of the m...

Ngày tải lên: 23/01/2014, 04:20

11 442 0
Tài liệu Fundamentals of electromechanical energy conversion docx

Tài liệu Fundamentals of electromechanical energy conversion docx

... of the converted power that is defined as mec tp ω = (13) in terms of other known powers and derivation of the equation for motion of rotating masses in terms of known parameters and inputs of ... (23) Whatremainstobedoneistosubstituteallthepowersandderivativesofstored energies into the power balance equations (11)-(12). This enables, first of all, calculation of the converted...

Ngày tải lên: 23/01/2014, 06:20

22 366 0
Tài liệu Fundamentals of Machine Design P25 docx

Tài liệu Fundamentals of Machine Design P25 docx

... junctions we ld weld 9.2.2.4F- Method of construction of multilayered cylinder 3. Autofrettage In some applications of thick cylinders such as gun barrels no inelastic deformation ... known as Self- hooping or Autofrettage. This allows the cylinder to operate at higher fluid pressure. For a given autofrettage fluid pressure a given amount of inelastic defo...

Ngày tải lên: 27/01/2014, 14:20

14 399 0
Tài liệu Start Here! Fundamentals of Microsoft .NET Programming docx

Tài liệu Start Here! Fundamentals of Microsoft .NET Programming docx

... Microsoft Press Book Support at mspinput@microsoft.com. Please note that product support for Microsoft software is not offered through the addresses above. We Want to Hear from You At Microsoft ...  What the different kinds of computers are and how the type of computer being used inuences the performance of various kinds of programs  How to assess the speed of a computer and...

Ngày tải lên: 16/02/2014, 06:20

265 2,8K 0
FUNDAMENTALS OF ESTHETIC IMPLANT DENTISTRY docx

FUNDAMENTALS OF ESTHETIC IMPLANT DENTISTRY docx

... schu@csdny.com E-mail2: schudmd@aol.com FUNDAMENTALS OF ESTHETIC IMPLANT DENTISTRY Abd El Salam El Askary FUNDAMENTALS OF ESTHETIC IMPLANT DENTISTRY FUNDAMENTALS OF ESTHETIC IMPLANT DENTISTRY Diagnostic ... of the hard or soft tissues, depending on the nature of the defect (B-w). Compromised bone necessitates osteoplasty and some form of hard or soft tissue augmentation de...

Ngày tải lên: 06/03/2014, 12:20

355 367 2
w