Báo cáo hóa học: " Fabrication of Anti-human Cardiac Troponin I Immunogold Nanorods for Sensing Acute Myocardial Damage" doc

... of conventionally spher- ical gold nanoparticles. Keywords Gold nanorod Á Biosensor Á Surface modification Á Cardiac troponin I Introduction Cardiac troponin I (cTnI) is a protein subunit of cardiac troponin ... detection of cTnI in the serum of patients with a higher risk of acute myocardial infarction can decrease the danger of death from heart attack. Because...

Ngày tải lên: 22/06/2014, 00:20

... to their unique physicochemical properties and prom- ising applications in nanodevices [1, 2]. One of the major challenges for nanodevice fabrication is how to immobilize the functional nanostructures ... particle size distribution of b. The inset in a is a SAED pattern of an Au nanoparticle Fig. 5 Schematic diagram of the two-step preparation method. The preloaded Au nanoparticle...

Ngày tải lên: 21/06/2014, 20:20

... approximately 1.74 keV in 1% Sil-PFA composite membranes. As the loading of silicalite increases, the intensity of silicon peak increases. This clearly indicates the presence of silicalite nanocrys- tals ... values for crystalline nanosilicalite [15,25]. The SEM images of silicalite nanocrystals shown in Figure 1 rev eal uniform spherica l nanopa rticles and a narrow particle size d...

Ngày tải lên: 20/06/2014, 23:20

... capabilities. Comparison of rate capabilities in pure ZW and C-ZW nanorods at diff erent current rates. The open-square curv e indicates the coulombic efficiency of the C-ZW nanorods. (By HW Shim ... Immediate publication on acceptance 7 Open access: articles freely available online 7 High visibility within the fi eld 7 Retaining the copyright to your article Submit your next manuscrip...

Ngày tải lên: 20/06/2014, 23:20

... Tsunozaki 2 Abstract UV curing nanoimprint lithography is one of the most promising techniques for the fabrication of micro- to nano- sized patterns on various substrates with high throughput and a low production cost. ... replicated on various substrates, including a flat Si substrate and curved acryl substrate, with high fidelity using UV nanoimprint lithography. Introduction In ord...

Ngày tải lên: 21/06/2014, 02:20

... provides an atomically smooth GaAs surface, which is a critical requirement for subsequent se lective III-V growth during device fabrication. In fact, prelimin- ary III-V molecular beam epitaxy ... Convenient online submission 7 Rigorous peer review 7 Immediate publication on acceptance 7 Open access: articles freely available online 7 High visibility within the fi eld 7 Retaining the copyr...

Ngày tải lên: 21/06/2014, 03:20

... 1:440. 28. Vakarelski IU, Brown SC, Higashitani K, Moudgil BM: Penetration of Living Cell Membranes with Fortified Carbon Nanotube Tips. Langmuir 2007, 23:10893. 29. Boron WF: Regulation of intracellular ... biological, and medical applications. In particular, intracellular pH is an interest factors to most biologists because changes in intracellular pH affect the ionization state of al...

Ngày tải lên: 21/06/2014, 04:20

... anodization using Ti-foil (Figure 1a). The top surface of the TNT is always covered with some kind of oxide layer (Figure 1b) irrespective of the anodizing time. The oxide layer can be removed with ... essential for the formation of nano-porous struc- ture. A ccording to Stokes-Einstein relation, the diffusion coefficient is inversely proportional to the viscosity of the electrol...

Ngày tải lên: 21/06/2014, 04:20

... Convenient online submission 7 Rigorous peer review 7 Immediate publication on acceptance 7 Open access: articles freely available online 7 High visibility within the fi eld 7 Retaining the copyright ... thus avoiding the use of sophisticated device fabrication procedures. In addition, the highly ordered porous alumina on Al foils with the help of pre- patterned indentations by the above...

Ngày tải lên: 21/06/2014, 05:20