Surface Integrity Cutting Fluids Machining and Monitoring Strategies 10 potx
Surface Integrity Cutting Fluids Machining and Monitoring Strategies_1 pdf
... Johnson, 2001] . Machining and Monitoring Strategies tion machining strategy (i.e. see Fig. 216) and, they can be succinctly summarised as follows: • Direct benets – improved machining eciency, – ... Yamazaki Mazak Corporation] . Machining and Monitoring Strategies Figure 214. Graphical relationship of high speed machining of metals – according to Salomon...
Ngày tải lên: 21/06/2014, 22:20
Surface Integrity Cutting Fluids Machining and Monitoring Strategies_2 doc
... and its operation. Machining and Monitoring Strategies Figure 222. The CNC control problem of servo-lag and its aect on the associated HSM motional kinematics. Machining and Monitoring Strategies ... rotating cutting tool to rest and press against machined surface and thus, generate minute ‘gouging-eects’ in the surface. (Source: Seames, 1990; Smith, 1993)...
Ngày tải lên: 21/06/2014, 22:20
Surface Integrity Cutting Fluids Machining and Monitoring Strategies_4 pdf
... Precision Inc. (HPI)] . Machining and Monitoring Strategies Figure 233. A graph to determine high-speed cutter unbalance ‘U’ (ANSI S2.19–1989). Machining and Monitoring Strategies Figure ... HSM?’ Is it: • High rotational speed machining? • High cutting speed machining? • High feed machining? • High speed and feed machining? • High productivity machin...
Ngày tải lên: 21/06/2014, 22:20
Surface Integrity Cutting Fluids Machining and Monitoring Strategies_6 pdf
... and Gull, 2001] . Machining and Monitoring Strategies cally-ground on the three register diameters, with the top and bottom faces being surface ground. Previous to this heat-treatment and ... & Gull, 2001] . Machining and Monitoring Strategies (Fig. 239b). So, by the simple action of turning a hand wheel at its end, the tools could be simultaneously ope...
Ngày tải lên: 21/06/2014, 22:20
Surface Integrity Cutting Fluids Machining and Monitoring Strategies_7 doc
... The complex machining of either a sculptured, or die and mould surfaces, will usually necessitate both multifarious and sophisticated programming techniques . Machining and Monitoring Strategies ... the adverse and miscalcu- lated cutting data, there is a likelihood for premature cutting edge frittering and chipping – created by too low a cutting speed and localise...
Ngày tải lên: 21/06/2014, 22:20
Surface Integrity Cutting Fluids Machining and Monitoring Strategies_9 ppt
... dimensional and surface texture characteristics. [Source: Lamb & Gull, 1999] . Machining and Monitoring Strategies Figure 255. Some typical micro-tooling: drills and boring tools. Machining and ... instru- ment/equipment uncertainty. (Source: Figliola and Beasley et al., 2000) Machining and Monitoring Strategies tioned, ultra-precision machining doe...
Ngày tải lên: 21/06/2014, 22:20
Surface Integrity Cutting Fluids Machining and Monitoring Strategies_10 potx
... (Figs. 116 and 117), or non-contact variet- ies (not depicted), Machining and Monitoring Strategies Tool – Force Monitoring In single-point turning, if one ignores the orthogonal cutting condition, ... both the tools and their setting osets, monitoring for tool wear and breakage and, initiat- ing tool replacements – as necessary, • Adjusting speed and feed as appr...
Ngày tải lên: 21/06/2014, 22:20
Surface Integrity Cutting Fluids Machining and Monitoring Strategies_11 pdf
... 7075 and AISI 1945 Steel in High Speed Machining. Trans. of NAMRI/SME, Vol. 28, 101 106 , 2000. Sims, C. Hope, A.D., Smith, G.T. and Gull, M. Correlation of Machine Tool and CMM Accuracy and ... 1994. Schulz, H. and Hock, S. High Speed Milling of Turbine Blades. Machining and Monitoring Strategies In the relatively near-future, the application of AI to the tasks in...
Ngày tải lên: 21/06/2014, 22:20
Thermodynamics Interaction Studies Solids, Liquids and Gases Part 10 potx
... Hence, the Landau theory based on the mean-field approximation has error which diverges as the system approaches to the critical point. Mathematically, the Landau theory expands the Landau function ... + 2OH - (H 2 O) 10 252.9 5.01 10 -45 Table 2. Calculated ΔG ads (kJ/mol) and equilibrium adsorption constant K at 25 °C of arsenate on various protonated Ti-(hydr)oxide surfaces. Met...
Ngày tải lên: 19/06/2014, 08:20
Nuclear Power System Simulations and Operation Part 10 potx
... primary pump and pressurizer indicated Parameter Value V (cm 3 ) 1.485 10 9 L (g/s) 2.3 Q (g/s) 470 D 2.5 10 -3 W (g) 1.072 10 9 β 0.001 F (Fissions/W.s) 3.03 10 10 P o (MW th ) ... assessment and safety analysis. Lumping of parameters and grouping of similar elements simplifies many features of these codes and adds to their computational efficiency. The M...
Ngày tải lên: 19/06/2014, 15:20