Manufacturing the Future 2012 Part 14 pot

... and the particle size ratio is defined as the ratio of the size of the large par- ticle to the size of the small particle. (a) The effect of the particle size ratio To exam the effect of the particle ... called the thin plate model. The dimensions of the thin plate are shown in Fig. 16, where t is the thickness of the plate and L is the edge dimension of t...

Ngày tải lên: 21/06/2014, 19:20

... life to the contract. The contract starts at the moment the acceptance reaches the offeror. The cluster manager, and the candidate agents when negotiating the cluster contract will use the offeror-acceptance ... shows the registering sequence in the cluster of two MRAs. Figure 17 shows the main user interface of the agent (CA/MRA) (left part) . The right part...

Ngày tải lên: 21/06/2014, 19:20

... a : the number of parts visit both machines; b : the number of parts visit machine i but not j ; c : the number of parts visit machine j but not i ; d : the num- ber of parts visit neither ... co- efficients, rather than evaluating the similarity between two objects, they evaluate the “appropriateness” between them. Manufacturing the Future: Concepts, Technologies &am...

Ngày tải lên: 21/06/2014, 19:20

... pallet and moved out of the system. The speed of the AGV is set at 175 feet/minute. Parts arrive to the system on pallets containing 4 parts of type 1, 2 parts of type 2, and 2 parts of type 3 every ... the aged-based model, if a failure oc- curs before the scheduled PM, PM is rescheduled from the time the corrective Manufacturing the Future: Concepts, Technologies &a...

Ngày tải lên: 21/06/2014, 19:20

... in the direction of axis OY. Manufacturing the Future: Concepts, Technologies & Visions 640 Wi is the weight of the powder component i, and ρ i is the theoretical density of the ... object from the test set. One set of 314 parts with 19 defectives is used as the test set. The accuracy of results for 314 test set parts is shown in Table 7. As Pawlak (1991)...

Ngày tải lên: 21/06/2014, 19:20

... being sent to the SIEM which in turns moves the robot ma- nipulator to pick up the component. At the same time the camera moves on the working space detecting the Zone 2, where the fixed, female ... also sent to the SIRIO, to direct the robot towards the assembly point. Once the part is grasped and in contact with the female component the assembly operation is s...

Ngày tải lên: 21/06/2014, 19:20

... Fig- ure 6. The diameter of the circular peg was 25 mm and the side of the square peg was also 25 mm. The dimensions of the non-symmetric part, the radi- used-square, was the same as the squared ... width. The assembly was ended when 3/4 of the body of the peg were inside the hole. This represented 140 motion steps in the -Z assembly direction. Male Compo...

Ngày tải lên: 21/06/2014, 19:20

... consideration. The heaviest and bulkiest part is selected as a base part and then the assembly sequence contin- ues from heavy to light parts. The parts with the least volume, i.e. connective parts, ... stochastic. The new re- placement population is created by the selection of the best performing indivi- duals, among either the offspring or the parents of the offspr...

Ngày tải lên: 21/06/2014, 19:20

... System Theory, The Journal of Grey System, Manufacturing the Future: Concepts, Technologies & Visions 702 1. they must have the process experience required by the research goals, and 2. they ... without the pump. The volume of the pipe is able to calculate by using the length and square of the pipe. The water at the upstream is vacuumed depending on synchro...

Ngày tải lên: 21/06/2014, 19:20

... effective way. The issue is how to evaluate and then change the structure of the network. The evolution aspect of the supply chain network structure provides the basis for the change. The development ... loop from the scheduling system to the planning system, the decision made by the scheduling system does not affect the decision at the planning stage; however,...

Ngày tải lên: 21/06/2014, 19:20