Manufacturing the Future 2012 Part 8 pptx

... 0,1 rad 33 rad No 1 ,82 57,6 143,1 131° 2,4 1,9 -9 82 ,8 102,0 -1 ,8 0,3 rad 34 circle No 1, 28 58, 5 43 ,8 145° 16,2 1,2 -5 78, 5 103,0 -1 ,8 0,3 circle Manufacturing the Future: Concepts, Technologies ... 177,7 147 12° -2,70 -2 2 82 ,8 103,0 0,5 1 square 21 square No 1 ,8 57,6 142,1 15° 2,4 2,9 -5 83 ,8 102,0 -0,5 0 ,8 square 22 rad No 1 ,84 61,5 45,7 26° 14,3 -0,7...

Ngày tải lên: 21/06/2014, 19:20

... 5.002.000 )80 0( = at 80 0=k , and the system parameters are changed to 4= ρ . The controller stabilizes the system in sec 2 under no information of the system changes, either the perturbation of the ... update gains. The results indi- cate that the proposed controller can stabilize the system with uncertainty in Manufacturing the Future: Concepts, Technologies &...

Ngày tải lên: 21/06/2014, 19:20

... life to the contract. The contract starts at the moment the acceptance reaches the offeror. The cluster manager, and the candidate agents when negotiating the cluster contract will use the offeror-acceptance ... shows the registering sequence in the cluster of two MRAs. Figure 17 shows the main user interface of the agent (CA/MRA) (left part) . The right part...

Ngày tải lên: 21/06/2014, 19:20

... 99 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 1972 McAuley (Jaccard) 1 980 D e W itte (production volum e) 1 985 Selvam (O peration sequences) 1 989 G unasingh (Tooling ... 85 85 85 89 69 91 75 88 73 Table 13. The number of problems to which Jaccard gave the best performance values Application Similarity Coefficient Method To Cellular Ma...

Ngày tải lên: 21/06/2014, 19:20

... 5 5 7 6 8 7 8 8 7 8 9 9 8 8 7 7 17 Relative match- ing 5 4 4 8 7 9 9 9 9 9 9 9 5 9 6 8 18 Chandraseharan & Rajagopalan 2 5 8 6 9 8 8 8 7 7 9 9 9 9 6 7 19 MaxSC 1 4 8 6 9 8 8 8 7 7 9 ... 7 8 8 9 9 9 9 9 9 7 7 12 PSC 2 2 9 8 9 9 9 8 9 9 9 9 9 9 8 9 13 Dot-product 3 5 9 8 7 9 8 9 9 9 9 9 9 9 7 7 14 Kulczynski 2 5 8 7 8 8 8 8 9 9 9 9 9 9 7...

Ngày tải lên: 21/06/2014, 19:20

... -6 83 .2 101 .8 1.7 -0.7 Y 13 R N 1:22 38. 3 61.5 146 119 -0.7 0.6 -1 84 .8 102 .8 0.1 -1.7 Y 14 R N 1:22 36 .8 63.4 43 .8 126 -0 .8 1.7 -4 83 .6 101 .8 1.6 -0.7 Y 15 R N 1:24 36.6 179.6 47.7 1 38 0 ... O (N * 8* 4) where N is the size of the perimeter, and 8 & 4 are the number of comparisons the algorithm needs to find the pixel farer to the boundary, th...

Ngày tải lên: 21/06/2014, 19:20

... consideration. The heaviest and bulkiest part is selected as a base part and then the assembly sequence contin- ues from heavy to light parts. The parts with the least volume, i.e. connective parts, ... feasible. The number of nodes is reduced from 15 to 8 in the di- Manufacturing the Future: Concepts, Technologies & Visions 486 volume of the gear in the g...

Ngày tải lên: 21/06/2014, 19:20

... in the direction of axis OY. Manufacturing the Future: Concepts, Technologies & Visions 640 Wi is the weight of the powder component i, and ρ i is the theoretical density of the ... 126.4 7 94 .8% 120 .8 6.4 4.4 1 .8 127.2 6.2 95.4% 1 1 18 7 9 0 125 9 93.3% 122 8 3 0 130 3 97.7% 2 121 6 4 3 127 7 94 .8% 121 8 4 0 129 4 97.0% 3 122 7 2 2 129 4 97.0% 122 9 2...

Ngày tải lên: 21/06/2014, 19:20

... and the particle size ratio is defined as the ratio of the size of the large par- ticle to the size of the small particle. (a) The effect of the particle size ratio To exam the effect of the particle ... results, the size ratio of the large parti- cle to the small particle should be higher than at least 6 .82 so that all small par- ticles can enter the interstice...

Ngày tải lên: 21/06/2014, 19:20

... 8. 656 0.0 38 7 10 13.142 0.314 27 8 8. 180 0.022 8 29 - - 28 8 7.730 0.034 9 7 7.000 - 29 7 7.304 0.043 10 8 7 .82 6 0.022 30 7 6.903 0.014 11 8 8.320 0.040 31 9 8. 845 0.017 12 9 8. 845 0.017 ... ISBN: 080 31222 68. ASTM F657. (1995). Annual Book of ASTM Standards, ISBN: 080 31222 68. Deng, J. (1 989 ). Introduction to Grey System Theory, The Journal of Grey System,...

Ngày tải lên: 21/06/2014, 19:20