Manufacturing the Future 2012 Part 5 potx

... Taube 1985b 20*20 3, 4 50 . Boe & Cheng 1991 20* 35 4 51 . Ng 1993 20* 35 4 52 . Kumar & Kusiak 1986 23*20 2, 3 53 . McCormick et al. 1 972 24*16 6 54 . Carrie 1973 24*18 3 55 . Chandrasekharan ... ),1( ),( jkik jkik jkik jkik aa aa aaP aa δ (5) ⎩ ⎨ ⎧ = .otherwise ,0 ,part uses machine if ,1 ki a ik (6) k : part index (k =1,… P ), is the k th part in the machin...

Ngày tải lên: 21/06/2014, 19:20

... Shop Floor Agility 55 acceptance validates and gives life to the contract. The contract starts at the moment the acceptance reaches the offeror. The cluster manager, and the candidate agents ... shows the registering sequence in the cluster of two MRAs. Figure 17 shows the main user interface of the agent (CA/MRA) (left part) . The right part shows the window...

Ngày tải lên: 21/06/2014, 19:20

... in the specified MTBF MTBF α β 50 0 250 2 150 0 750 2 250 0 1 250 2 Gamma 4000 2000 2 50 0 2 56 4.2 150 0 2 1692.2 250 0 2 2820. 95 Weibull 4000 2 451 3 .5 MTBF a b m 50 0 0 11 25 3 75 150 0 ... thus b= 450 0/4 = 11 25 and m=b/3= 150 0/4=3 75. Similarly, for MTBF= 150 0, b=33 75 and m=11 25. For MTBF= 250 0, b =56 25 and m=18 75. For MTBF=4000, b=9000 and m...

Ngày tải lên: 21/06/2014, 19:20

... yC STC - 25 +28 55 .106 24. 457 60° 60° - 25. 0 75 CTC - 25 +28 55 .078 24.600 60° 60° - 25. 0 75 Table 4. Working dimension of the CTC and the proposed STC (mm) 5. 5. Comparative analysis of the proposed ... 6 15 ON’ N EF BC 0±0.5T N∥Y 0±0.5T N⊥X L NE ±0.5T NE N’ X ±0.5T NX N’ y ±0.5T Ny 30°±0.5T α2 L CF =54 ±0.0 95 60°±0.5T αN L BC ±0.5L BC T α1 yc=L OD = 25. 0 65 0....

Ngày tải lên: 21/06/2014, 19:20

... 103,0 3,9 2,9 rad 5 rad Yes 1,86 56 ,6 143,1 36° 3,4 1,9 -4 82,8 103,0 0,6 2,9 rad 6 rad Yes 1,29 58 ,5 44,8 55 ° 15, 2 0,2 5 80,7 102,0 1 ,5 2,3 rad 7 circle Yes 1,12 172,8 46,7 57 ° 2,20 -1,7 -3 ... circle No 1,28 58 ,5 43,8 1 45 16,2 1,2 -5 78 ,5 103,0 -1,8 0,3 circle Manufacturing the Future: Concepts, Technologies & Visions 372 Zone 1 which is located on the...

Ngày tải lên: 21/06/2014, 19:20

... Fig- ure 6. The diameter of the circular peg was 25 mm and the side of the square peg was also 25 mm. The dimensions of the non-symmetric part, the radi- used-square, was the same as the squared ... system in Zone 1. Manufacturing the Future: Concepts, Technologies & Visions 420 The 2 peaks in the histogram represent the background and the pieces in...

Ngày tải lên: 21/06/2014, 19:20

... Journal of Intelligent Manufacturing, Vol. 15, 54 3 -59 , ISSN: 0 956 -55 15. Sinanoğlu, C. & Börklü, H.R. (20 05) . An Assembly Sequence Planning System for Mechanical Parts Using Neural Network, ... from the inital solution: X1=100; X2 =50 ; X3= -50 ; X4=20°; X5=0°; F=1.013E8; The improvement is hardly noticable, the solution proposed is: X1=100; X2 =50 ; X3=-26; X4...

Ngày tải lên: 21/06/2014, 19:20

... defined as the ratio of the weight of the large particle to the total weight of the powder mix- ture and the particle size ratio is defined as the ratio of the size of the large par- ticle to the size ... has 5 companies. The most of the upstream company is a parts manufacturing, and supply lead-time is 14days (2week). Manufacturing the Future: Concepts, Te...

Ngày tải lên: 21/06/2014, 19:20

... Joint-venture 55 .30 Labor union Labor union present 30. 45 No labor union 69 .55 Main product classifications Body parts 21.42 Chassis parts 25. 58 Suspensions parts 12. 25 Electrical parts 8.20 ... 0.030 2 7 7.387 0. 055 22 11 10 .59 2 0.037 3 9 8.290 0.079 23 5 5.374 0.0 75 4 9 9.302 0.034 24 3 2.726 0.091 5 11 10.438 0. 051 0. 055 25 9 9.160 0.018 6 10 11.712 0.1...

Ngày tải lên: 21/06/2014, 19:20

... 2. 15 2. 15 2. 25 2.30 2. 15 2.20 2. 35 2.40 2. 25 2 .50 C 2.00 2.20 2.20 3.20 3. 25 2. 25 1.10 1. 25 2. 05 2.10 1. 35 2.30 D 2.20 2 .50 2.20 2 .50 1.30 2.20 3 .50 1.20 2.20 3.70 2.60 2.40 Table 6. Price ... parameters. 0 5 10 15 20 25 30 35 40 45 1234 56 78 9101112 1314 151 6 Settings % Figure 5. Percentage improvement of the adaptive coordination mechanis...

Ngày tải lên: 21/06/2014, 19:20