NAVFAC P-433 Welding Materials Handbook 1 pot
NAVFAC P-433 Welding Materials Handbook_1 pot
... E-7 018 NSN: 9GD 3439-00 -16 5- 418 6 (1/ 8X 14 ) 9GD 3439-00-479 -10 99 (5/32X 14 ) 9GD 3439-00-853-2 719 (3 /16 X 14 ) POSITION: All POLARITY: AC or DC Reverse RECOMMENDED AMPERAGES: 1/ 8 -10 0 to 15 0 5/32 -12 0 ... 9GD 3439-00 -16 5- 418 9 (1/ 8X 14 ) 9GD 3439-00 -16 5- 418 8 (5/32X 14 ) POSITION: All POLARITY: AC or DC Reverse RECOMMENDED AMPERAGES: 1/ 8 - 80 to 12 0 5/32 -90 t...
Ngày tải lên: 20/06/2014, 18:20
NAVFAC P-433 Welding Materials Handbook_2 pot
... (tungsten, high speed) NSN: 3439-00 -10 5-9948 (1/ 4X 14 ) 3439- 01- 032-5978 (1/ 16 X 14 ) 3439-00-902-4 210 (3 /16 X 14 ) 3439-00 -10 5-9945 (3/32 X 14 ) 3439- 01- 012 -10 02 (3/64 X 14 ) POSITION: All POLARITY: ... 3439-00 -16 5- 417 8 (1/ 8X 14 ) 9GD 3439-00 -16 5- 417 9 (5/32X 14 ) 9GD 3439-00 -16 5- 418 0 (3 /16 X 14 ) POSITION: Flat - horizontal POLARITY: AC -DC Straight RE...
Ngày tải lên: 20/06/2014, 18:20
NAVFAC P-433 Welding Materials Handbook_7 potx
... Electrode: Page 1- 26 Primary Electrode: Page 1- 26 Alternate Electrodes: Pages 1- 25 or 1- 22 Alternate Electrodes: Pages 1- 25 or 1- 22 Welding Procedures. Apply hard-facing to top and Welding Procedures: ... (Continued) Grapple Tines Carbon Steel Primary Electrode: Page 1- 26 Alternate Electrodes: Pages 1- 25 or 1- 22 Welding Procedures: Hard-face tine up about 10 in. from...
Ngày tải lên: 20/06/2014, 18:20
NAVFAC P-433 Welding Materials Handbook_9 potx
... usefulness. ATOMIZED METALLIC MATERIALS KIT NSN: 8030- 01- 232 -12 46 CODE M- 41 M-42 M-43 M-44 M-50 M-5 1 M-52 * 2 Units * 1 Unit * 1 Unit * 1 Unit 18 OZ. 1 Pint ** 1 each 2 each 2 each Alloy GP Metal Smoothcoat ... compound Putty DIRECTIONS FOR USE. 1) See general information. 2) Mix reactor (R) into Base Alloy (A) in ratios: By Volume -1 part A to 1 part R By Weight...
Ngày tải lên: 20/06/2014, 18:20
Handbook of plant based biofuels - Chapter 1 potx
... contents Abstract 3 1. 1 Introduction 3 1. 2 The World Energy Scenario 4 1. 3 Renewable Energy 6 1. 3 .1 Hydroelectricity 6 1. 3.2 Solar Power 6 1. 3.3 Wind Power 6 1. 3.4 Geothermal Power 6 1. 3.5 Tidal Power 7 1. 3.6 ... 7 1. 3.6 Biofuels 7 1. 4 Biofuels for the Transportation Sector 7 1. 5 Status of Biofuel 9 1. 6 Bioethanol 9 1. 7 Biodiesel 11 References 12 © 2009 by T...
Ngày tải lên: 20/06/2014, 00:20
NAVFAC P-433 Welding Materials Handbook_3 pdf
... Blocks Primary Electrodes Arc 1- 20 1- 20 1- 17 1- 20 1- 17 1- 17 1- 32 1- 17 1- 22 1- 17 Torch 1- 15 1- 15 1- 15 1- 1o Alternate Electrodes Arc 1- 17 1- 17 1- 20 1- 17 1- 20 1- 20 1- 20 1- 17 1- 20 Torch 1- 1o 1- 1o 1- 1o 1- 1o 1- 1o 1- 12 1- 15 1- 35 Simpo ... Steel Primary Electrodes Arc 1- 1 1- 3 1- 5 1- 3 1- 1 1- 3 1- 22 1- 27 1- 27 1- 27 GMA 1-...
Ngày tải lên: 20/06/2014, 18:20
NAVFAC P-433 Welding Materials Handbook_4 ppt
... STEELS Metal Designation SAE 2 015 Steel SAE 211 5 Steel 2 -1/ 2% Nickel Steel SAE2 315 Steel SAE 2320 Steel SAE 2330 Steel SAE 2340 Steel SAE 311 5 Steel SAE 312 5 Steel SAE 313 0 Steel SAE 314 0 Steel SAE 315 0 Steel SAE 3 215 Steel SAE ... require NICKEL (Ni) 25 -12 Type 309 preheating but it maybe COLUMBIUM (Cb) 25-20 Type 310 desirable to remove STAINLESS STEEL 18 -8 Cb. Type 347 chill...
Ngày tải lên: 20/06/2014, 18:20
NAVFAC P-433 Welding Materials Handbook_5 pdf
... tooth as shown in Figure 2 -11 . FIGURE 2 -11 . Hard-Facing Ripper Teeth 2-22 Bulldozer End Bits Carbon Steel Primary Electrode: Page 1- 25 Alternate Electrodes: Pages 1- 22, 1- 20 Welding Procedures: Place ... page 1- 25 as a primary choice, and electrodes on page 1- 22, or 1- 27 as alternate choices. For extreme abrasion, use electrodes on page 1- 26 as a primary choice and electro...
Ngày tải lên: 20/06/2014, 18:20
NAVFAC P-433 Welding Materials Handbook_10 ppt
... (cfh) (Inches) 72-70 1/ 4 1- 2 5-6 1- 3 UP TO 1/ 32 65-60 7 /16 1- 3 5-6 2-4 1/ 32 -1/ 16 56-54 5/8 1- 5 6-8 3-8 1/ 16 -1/ 8 49-48 1 2-8 8 -10 5 -18 1/ 8-3 /16 43-40 1 1/8 3-9 10 -12 6-30 3 /16 -1/ 4 36 1 1/4 5-1o 12 -15 6-35 1/ 4-3/8 * ... have No. 69 drill-size flame ports counterbored 1/ 16 in. deep with No. 56 drills. The rows and ports are on 1/ 8 in. centers and t...
Ngày tải lên: 20/06/2014, 18:20
NAVFAC P-433 Welding Materials Handbook_11 docx
... . . . . . . . . . . . . . . . . . . 2-64 2-23 2-22 2-40 2-43 2 -12 2-80 2-67 2-63 2-49 2-50 2-50 2- 51 2- 41 2-42 2- 41 2-20 2-84 2 -15 2-58 2-58 Index-4 Simpo PDF Merge and Split Unregistered Version ... in. pipe cap, thread a 1/ 2 in. pipe to its center, then (for aspirated air), drill 10 equally spaced 1/ 4 in. holes on a 2-7/8 in. diameter circle and 10 equally spaced 1/ 4 in. h...
Ngày tải lên: 20/06/2014, 18:20