Fuel Injection Part 8 ppt
... 89 9 89 9 89 9 88 9 88 9 87 9 87 9 87 9 86 9 86 9 86 9 87 9 87 9 85 9 84 9 83 9 83 9 81 9 799 799 739 86 9 x y 0 0,2 0,4 0,6 0 ,8 1 1,2 1,4 0,4 0,5 0,6 0,7 0 ,8 0,9 529 679 739 659 84 9 88 9 89 9 89 9 88 9 87 9 86 9 85 9 81 9 749 789 80 9 81 9 799 789 769 709 82 9 83 9 84 9 85 9 82 9 x y 0 ... 89 9 89 9 89 9 88 9 88 9 87 9 87 9 87 9 86 9...
Ngày tải lên: 20/06/2014, 11:20
Fuel Injection Part 3 ppt
... 5.32 7. 38 0.721 1100 170 6.47 9.43 0. 686 1300 170 6 .87 10.30 0.666 300 200 3.63 6. 18 0. 587 700 200 6.74 10.20 0.660 1100 200 8. 53 13.10 0.653 1300 200 9.29 14.30 0.651 Table 1. Injection ... 5.32 7. 38 0.721 1100 170 6.47 9.43 0. 686 1300 170 6 .87 10.30 0.666 300 200 3.63 6. 18 0. 587 700 200 6.74 10.20 0.660 1100 200 8. 53 13.10 0.653 1300 200 9.29 14.30 0.651 Ta...
Ngày tải lên: 20/06/2014, 11:20
Fuel Injection Part 6 ppt
... celerity and ± 18% for kinematic viscosity. K ρ j= 0 j= 1 j= 2 K ρ1,j 8. 3636e2 -6.7753e-1 - K ρ2,j 1.5063e2 -2.4202e-1 - K ρ3,j 1.7 784 e-1 1.4640e-3 1.5402e-5 K ρ4,j 7 .81 09e-1 -8. 189 3e-4 - K E j= ... K p E l E p d p t p (15) Fuel Injection9 4 Fuel- air mixing increases as the fuel nozzle holes orifice diameter fuel nozzle holes decreases. Also soot incandescence is observe...
Ngày tải lên: 20/06/2014, 11:20
Fuel Injection Part 1 pptx
... controlled Port Fuel Injection (PFI) systems instead of fuel system with carburetor have been used since 1 980 ’s. In fuel injection systems, induced air can be metered precisely and the fuel is injected ... publication@sciyo.com Fuel Injection, Edited by Daniela Siano p. cm. ISBN 9 78- 953-307-116-9 Fuel Injection1 2 mounted on the rail are opened by Engine Control Un...
Ngày tải lên: 21/06/2014, 01:20
Fuel Injection Part 12 ppt
... 3.052 8 H7 28. 7 5 .84 9 3.095 16 H8 26.3 5 .84 9 3.102 24 H9 24.0 5.922 2 .88 8 50 0 H10 27.4 5 .82 5 2.961 8 H11 28. 8 5.934 2.955 16 H12 28. 8 6.251 3.01 24 H13 27.5 6.013 2.967 -1 2 H14 27 .8 ... 3.052 8 H7 28. 7 5 .84 9 3.095 16 H8 26.3 5 .84 9 3.102 24 H9 24.0 5.922 2 .88 8 50 0 H10 27.4 5 .82 5 2.961 8 H11 28. 8 5.934 2.955 16 H12 28. 8 6.251 3.01 24 H13 2...
Ngày tải lên: 21/06/2014, 01:20
... mass elements belong, the departments they represent, or the space IDs, you can use project parameters. You can create project parameters for program group, department, or space ID; assign ... as shown in Figure 7. 18 it may be just a face of a shape that you’ll need later to design a specific portion of a complex-shaped building, such as its roof. Figure 7. 18 NURBS shape created in .....
Ngày tải lên: 10/12/2013, 13:15
... it. Speaking UNIT 3 In Part 3 you will be presented with some more abstract questions. These will be broadly linked to the topic introduced in Part 2. You will have to take part in a discussion ... and first paragraph. Exchange these with a partner. Discuss what you would expect to read about in your partner's article. Read the whole of your partner's article when you have fin...
Ngày tải lên: 13/12/2013, 21:15
Tài liệu Tài liệu MCSA 70-290 Phần 2 - part 8 pptx
... 70-290 Tài liệu dành cho học viên VSIC Education Corporation Trang 211 MODULE 8: BẢO TRÌ PHẦN MỀM BẰNG DỊCH VỤ SUS Bài tập 1 Tạo GPO để cấu hình Automatic Updates Dùng
Ngày tải lên: 14/12/2013, 13:15
Tài liệu Master toefl vocabulary part 8 pptx
... is 9. g. The correct answer is 2. h. The correct answer is 8. i. The correct answer is 3. 04_TOEFL Vocab,Ch4,60-92 8/ 4/06, 12: 386 8 62 PART III: TOEFL Vocabulary Review ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○ ○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○○ www.petersons.com Study ... conference. (A) documented (B) lo...
Ngày tải lên: 14/12/2013, 13:15