Lasers Applications in Science and Industry Part 10 pptx

... the 105 0 aluminum alloy is about twice that of the 2024 aluminum alloy. Lasers – Applications in Science and Industry 174 Fig. 1. Schematic representation of propagation of pitting ... anodized aluminum in solutions. Fig. 10. Changes in the aspect ratios of fabricated artificial pits as a function of irradiation time. Lasers – Applications in Scienc...

Ngày tải lên: 18/06/2014, 22:20

... image quality while introducing a minor increase in the size of the object, all without changing the optical imaging parameters. Lasers – Applications in Science and Industry 96 1.2 Pulsed ... (1) w - grating period λ - desorbing laser wave length Part 2 Laser-Matter Interaction Lasers – Applications in Science and Industry 110 Fig. 1. Laser-matt...

Ngày tải lên: 18/06/2014, 22:20

... volume, as shown in Figs. 8 and Fig. 9. Lasers – Applications in Science and Industry 218 irradiation of a certain number of laser pulses. The laser ablation and OCT imaging are repeated ... hard and soft tissues. In a human tooth, time variation Lasers – Applications in Science and Industry 224 (a) (b) (x10 7 ) 0 100 200 300 400 500 600 70...

Ngày tải lên: 18/06/2014, 22:20

... Lasers – Applications in Science and Industry 8 temperature of the ZnSe crystals increases. In the case of pulse lasers, an increases in the transient temperature ΔT in materials ... hexagonal and the orientation of each diffraction point is Lasers – Applications in Science and Industry Edited by Krzysztof Jakubczak Published by In...

Ngày tải lên: 18/06/2014, 22:20

... dramatically increased to within 2 s and then saturated after ~10 s. Some specific points were marked at 79 mJ/cm 2 of Fig. 10( d), and corresponding SEM images are shown in Figs. 10( a), 10( b), and 10( c), ... coatings at Sandia’s large optics coating operation Coating large optics goes hand in hand with large vacuum coating chambers. In Sandia’s case, the coating chambe...

Ngày tải lên: 18/06/2014, 22:20

... coating design plays in obtaining coatings Lasers – Applications in Science and Industry 42 and this interference leads to intensity peaks well below the incident intensity except in the ... uniform Lasers – Applications in Science and Industry 50 Regarding polishing, washing and cleaning of an optic prior to coating it, we point out that residual a...

Ngày tải lên: 18/06/2014, 22:20

... coupling Lasers – Applications in Science and Industry 58 We observed that only AlN was detected in the films obtained with laser sources B and C, while films obtained with source A contain ... 20 minutes. Fig. 1. PLD general setup used in the experiments reviewed in this chapter Lasers – Applications in Science and Industry 66 to the vibration...

Ngày tải lên: 18/06/2014, 22:20

... Lasers – Applications in Science and Industry 82 melting m T and vaporization f T points are 512 °C and 738 °C, respectively. It should be noted that f T is determined by the cross point ... ISSN 108 9-7550 Lasers – Applications in Science and Industry 76 the experimental and theoretical characterizations of the bumps are demonstrated. In the second...

Ngày tải lên: 18/06/2014, 22:20

... fiber and supercontinuum spectrum. (Courtesy of Dr. Ping Ying and Dr. Zairu Ma) Lasers – Applications in Science and Industry 120 Fig. 3.5. The ripples of SiO 2 antireflection coating ... to induce ionization and the material cannot directly absorb incident laser of low intensity. Photo-ionization consists Lasers – Applications in Science and Industry...

Ngày tải lên: 18/06/2014, 22:20

... treated in this chapter is the difference in refractive index of a transparent material from that of the adjacent medium. Lasers – Applications in Science and Industry 134 In this study, ... combination of a silica glass plate in contact with distilled water layer. Figure 2.2 shows the typical results. In this case, pulse laser is focused Lasers – Application...

Ngày tải lên: 18/06/2014, 22:20