Lasers Applications in Science and Industry Part 8 ppt

... water 1.0 0 .89 24 ethanol 0 .8 1.2 59 vacuum oil 0.9 23 7.5X10-9 Table 2. Material properties of liquid samples Lasers – Applications in Science and Industry 1 48 5. Summary and conclusion ... wave induces cavitation bubbles on its way to the focused point. Even so, one may see generation of many waves at reflected interface. Lasers – Applications in Science and Industry 1 38 where ... (2000), The initiation of fine grain pentaerythritol tetranitrate by laser-driven flyer plates, J. Appl. Phys. Vol. 88 , pp. 65- Lasers – Applications in Science and Industry 140 Fig. 3.3...

Lasers Applications in Science and Industry Part 1 ppt

... Lasers – Applications in Science and Industry 8 temperature of the ZnSe crystals increases. In the case of pulse lasers, an increases in the transient temperature ΔT in materials ... hexagonal and the orientation of each diffraction point is Lasers – Applications in Science and Industry Edited by Krzysztof Jakubczak Published by InTech Janeza Trdine 9, ... Lasers – Applications in Science and Industry, Edited by Krzysztof Jakubczak p. cm. ISBN 9 78- 953-307-755-0 Lasers – Applications in Science and Industry 10to the (100) LaAlO3...

Lasers Applications in Science and Industry Part 6 pptx

... imaging parameters. Lasers – Applications in Science and Industry 961.2 Pulsed laser driven lithography and patterning Direct laser interference lithography/patterning involving selective removal ... (1) w - grating period λ - desorbing laser wave length Part 2 Laser-Matter Interaction Lasers – Applications in Science and Industry 110 Fig. 1. Laser-matter interactions involve numerous ... expansion will induce various changes in refractive index, heat capacity, etc. Lasers – Applications in Science and Industry 100 Fig. 4. SEM image of lift- off patterning of 18 nm Au on...

Lasers Applications in Science and Industry Part 10 pptx

... (Yokogawa Electric Co., DL708E). Lasers – Applications in Science and Industry 186 Fig. 18. Changes in rest potential after the re-activation of 2024 aluminum alloy in 0.5 kmol m-3 H3BO3 ... anodized aluminum in solutions. Fig. 10. Changes in the aspect ratios of fabricated artificial pits as a function of irradiation time. Lasers – Applications in Science and Industry 188 Fig. ... lower with increasing aspect ratio. 4. The repassivation ratio at 0.01 s after activation becomes lower with increasing aspect ratio. Lasers – Applications in Science and Industry 184 Fig....

Lasers Applications in Science and Industry Part 12 pptx

... volume, as shown in Figs. 8 and Fig. 9. Lasers – Applications in Science and Industry 2 18 irradiation of a certain number of laser pulses. The laser ablation and OCT imaging are repeated ... abruptly narrower in the dentine, reflecting the large difference in hardness between enamel and dentine. In addition, in the real-time imaging shown in Fig. 5, a small flying particle (debris), ... enamel and dentine, and there is a remarkable difference in refractive index and hardness between these two materials. The interface between enamel and dentine is therefore recognized clearly in...

Lasers Applications in Science and Industry Part 2 pot

... shown in Fig. 11(a). Lasers – Applications in Science and Industry 28 4. Depositing high LIDT coatings at Sandia’s large optics coating operation Coating large optics goes hand in hand with ... coating chambers. In Sandia’s case, the coating chamber is 2.3 m x 2.3 m x 1 .8 m in size and opens to a Class 100 clean room equipped for handling and cleaning the large optics for coating ... detail in this chapter. Regarding the polishing and preparing of optics for coating, we have demonstrated in the case of an AR coating that using one combination of polishing compound and wash...

Lasers Applications in Science and Industry Part 3 pot

... coating design plays in obtaining coatings Lasers – Applications in Science and Industry 42 and this interference leads to intensity peaks well below the incident intensity except in the ... 75; Non-IAD: 82 for 1054 nm 32 deg Spol: (79), ( (82 )); Ppol: (88 ), ((79)), 70, 91 for 1054 nm 45 deg Spol: (82 ), ( (88 )), [88 ]; Ppol: (73), ((75)), [88 ], 58, 79, 88 , 88 , 91, 91, 97 ... uniform Lasers – Applications in Science and Industry 50Regarding polishing, washing and cleaning of an optic prior to coating it, we point out that residual amounts of the polishing compound...

Lasers Applications in Science and Industry Part 4 docx

... coupling Lasers – Applications in Science and Industry 58 We observed that only AlN was detected in the films obtained with laser sources B and C, while films obtained with source A contain ... 20 minutes. Fig. 1. PLD general setup used in the experiments reviewed in this chapter Lasers – Applications in Science and Industry 66to the vibration bath, which results in heating ... by the pre-pulse causing their gradual boiling and elimination. Ultimately, the Lasers – Applications in Science and Industry 54Pulse shaping introduces the method that makes possible the...

Lasers Applications in Science and Industry Part 5 pdf

... Lasers – Applications in Science and Industry 82 melting mT and vaporization fT points are 512 °C and 7 38 °C, respectively. It should be noted that fT is determined by the cross point ... m, and the size of the hole is about 250 300nm. Lasers – Applications in Science and Industry 88 We also chose six pattern units (marked by line in Fig. 13(b)) to measure the height and ... irradiation is well defined, and the patterns are very uniform and smooth. Lasers – Applications in Science and Industry 86 heated to above the decomposing temperature, and then the reaction happens....

Lasers Applications in Science and Industry Part 7 docx

... fiber and supercontinuum spectrum. (Courtesy of Dr. Ping Ying and Dr. Zairu Ma) Lasers – Applications in Science and Industry 120 Fig. 3.5. The ripples of SiO2 antireflection coating ... to induce ionization and the material cannot directly absorb incident laser of low intensity. Photo-ionization consists Lasers – Applications in Science and Industry 114 (a) Original ... Pathways to Melting, Ablation and Solidification in Absorbing Solids Under Pulsed Laser Irradiation,” Phys. Rev. B. 73, 1341 08, 2006. Lasers – Applications in Science and Industry 112...

Xem thêm