Toyota camry 2006 2011 clutch hệ thống ly hợp trên toyota camy đời 2006 2011

... to the clutch pedal. 5. INSTALL CLUTCH PEDAL PAD (a) Install the clutch pedal pad to the clutch pedal. 6. INSTALL CLUTCH PEDAL SPRING HOLDER (a) Apply MP grease to the inside of a new clutch ... INSPECT AND ADJUST CLUTCH PEDAL SUB- ASSEMBLY See page CL-4. CL–12 CLUTCH – CLUTCH MASTER CYLINDER CL TRANSMISSIONCLUTCH CLUTCH MASTER CYLINDER COMPONENTS COWL TOP PANEL OUTER SUB-...

Ngày tải lên: 24/05/2014, 13:28

... SUB- ASSEMBLY (a) Remove the 6 nuts and rear bumper reinforcement sub-assembly. REASSEMBLY 1. INSTALL REAR BUMPER REINFORCEMENT SUB- ASSEMBLY (a) Install the rear bumper reinforcement sub-assembly with ... screws. 19. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light) (See page LI-82) 20. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light) INSTALLATION 1. INSTALL FRONT BUMPER ASSEMBLY (w/o Fog Light)...

Ngày tải lên: 24/05/2014, 13:37

... page Only interior light does not illuminate 1. Bulb - 2. Personal light assembly (with sliding roof) LI-105 3. Rear room light assembly (without sliding roof) LI-108 4. Harness or connector - Only ... one direction 1. Headlight dimmer switch assembly (Turn signal switch) LI-120 2. Turn signal flasher assembly LI-138 3. Harness or connector - Only one bulb does not operate 1. Bulb - 2. Harnes...

Ngày tải lên: 24/05/2014, 13:43

... (Distortion) FLYWHEEL (Distortion) Symptom Clutch grabs/chatters 1 2 2 2 2 2 Clutch pedal spongy 1 2 Clutch noisy 1 Clutch slips 1 2 2 3 4 5 Clutch does not disengage 12 333333 3445 Revision: July 2011 ... 21 General Specifications 21 Clutch Pedal 21 Clutch Disc 21 Clutch Cover 21 Revision: July 2011 2012 Versa Sedan CL-20 < UNIT REMOVAL AND INSTALLATION > CLUTCH...

Ngày tải lên: 12/04/2014, 16:03

... frame assembly to the starter yoke assembly. NOTICE: The magnet of the starter yoke assembly may attract the starter armature assembly when the starter commutator end frame assembly is installed, ... ARMATURE ASSEMBLY (a) Apply high-temperature grease to the plate washer and the armature shaft. (b) Install the starter armature assembly to the starter commutator end frame assembly. (c) U...

Ngày tải lên: 23/05/2014, 16:53

... switch. • After approximately 1 hour has passed with the engine switch on (ACC) and the shift position in P, the main body ECU will automatically cut the power supply (the power source mode ... have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask ....

Ngày tải lên: 24/05/2014, 13:08

... differently, depending on the environment in which the person is situated. For example, a given amount of solar radiation can feel comfortably warm in a cold climate, or extremely uncomfortable ... with lots of cold water. CAUTION: Do not rub your eyes or skin. (b) Apply clean petroleum jelly to the skin. (c) Go immediately to a hospital or see a physician for professional treatment. 4....

Ngày tải lên: 24/05/2014, 13:13

... that all doors automatically lock when the shift lever is moved into any position from the P position (A/T). (2) When any door is unlocked after all doors automatically lock, check that all doors ... simultaneously by driver side door control switch Door control switch circuit (Driver side) DL-60 Replace main body ECU (Instrument panel J/B) - All doors cannot be locked/unlocked simultaneo...

Ngày tải lên: 24/05/2014, 13:29

... AXLE ASSEMBLY (a) Put matchmarks on the front drive shaft assembly and the axle hub. (b) Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly. NOTICE: Be ... inboard joint assembly. 7. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY (a) Remove the grease from the inboard joint assembly. (b) Put matchmarks on the inboard joint assembly and outboard joint...

Ngày tải lên: 24/05/2014, 13:30