laser based fabrication of polymer micropump

... Perspective view of the diffuser polymer micropump and (b) side view of the pump assembly (not to scale). Kim and Xu: Laser- based fabrication of polymer micropump 153J. Microlith., Microfab., Microsyst., ... 1 Hz. Fig. 10 Maximum deflection of the diaphragm as a function of fre- quency. Kim and Xu: Laser- based fabrication of polymer micropump 155J. Microlith...

Ngày tải lên: 06/05/2014, 08:53

... Perspective view of the diffuser polymer micropump and (b) side view of the pump assembly (not to scale). Kim and Xu: Laser- based fabrication of polymer micropump 153J. Microlith., Microfab., Microsyst., ... 1 Hz. Fig. 10 Maximum deflection of the diaphragm as a function of fre- quency. Kim and Xu: Laser- based fabrication of polymer micropump 155J. Microlith...

Ngày tải lên: 06/05/2014, 08:55

... ultraviolet ͑UV͒ excimer laser ab- lation of polymers for fabrication of microstructures used in microfluidic devices. Since the demonstration of UV laser ablation of polymers some 20 yr ago, 8 much ... manufacturing cost. Lasers have been widely used as a versatile manufacturing tool for decades and recently, research has been carried out on laser based MEMS fabrication. 1...

Ngày tải lên: 06/05/2014, 08:53

... 107–111 Wet process -based fabrication of WO 3 thin film for NO 2 detection Yong-Gyu Choi, Go Sakai, Kengo Shimanoe, Noboru Yamazoe ∗ Department of Materials Science, Faculty of Engineering Sciences, ... obtained was 450 nm in mean thickness. The film was a slim pack of square plates, each of which was a stack of thin lamellar crystals of WO 3 . The device was sensitive enough...

Ngày tải lên: 20/03/2014, 13:11

... print head, one of the most important elements in an ink-jet printing system, is a combination of microfluidics and microfabrication (MEMS) and is used to eject small amounts of fluid on target ... School of SungKynKwan University in partial fulfillment of the requirements for the degree of MASTER OF SCIENCE in Materials Science and Engineering June 2007 Depart...

Ngày tải lên: 10/04/2013, 13:48

... at the University of Paris XI, Orsay in 1981. Since 1986, he is Professor at the Uni- versity of Evry and he was the Head of Electrical Engineering Department of the Institute of Technology from ... Assistant Professor at the University of Evry. In 2000, he received the Habilitation à Diriger des Recherches diploma. He is the Head of the Electrical Engineering Department of th...

Ngày tải lên: 23/10/2013, 15:15

... factorization of the linear part of  U l,j+1 . (ii) Shift all but the constant part of  U l,j+1 to U r,j . Make Q the linear part of  U l,j+1 . Apply Q −1 on U r,j . (iii) Bound the range of the ... and V instead of a Taylor model vector. The symbolic variables are denoted by a and b (instead of the vector x). Example 5.1. Absorption of the interval part into the symbolic p...

Ngày tải lên: 12/01/2014, 21:46

... Taylor Model Based Integration of ODEs Interval Arithmetic and Taylor Models Verified Integration of ODEs Taylor Model Methods for ODEs Verified Integration of Linear ODEs On Taylor Model Based Integration ... M. Neher On Taylor Model Based Integration of ODEs Interval Arithmetic and Taylor Models Verified Integration of ODEs Taylor Model Methods for ODEs Verified Integration of...

Ngày tải lên: 12/01/2014, 21:47

... were selected. MALDI-TOF/TOF In addition to LC-MS ⁄ MS analysis, we also completed TOF ⁄ TOF analysis of selected peaks to confirm structure using a MDS Sciex 4800 MALDI-TOF ⁄ TOFÔ instru- ment (Applied ... software. TOF ⁄ TOF fragmentation spectra were recorded using negative-ion linear mode with stan- dardized MS ⁄ MS acquisition and processing methods after tuning of the instrument. TOF...

Ngày tải lên: 14/02/2014, 19:20