Lab 7 MapReduce
Lab 7.1.2 Waveform Decoding
... - 2 CCNA 1: Networking Basics v 3.0 - Lab 7. 1.2 Copyright 2003, Cisco Systems, Inc.
Lab 7. 1.2 Waveform Decoding
Objective
The purpose of this lab is to integrate knowledge of networking ... data
is available from the instructor. Decoding the waveform is a crucial step in understanding how
networks operate.
For the first part of the lab, all that is needed is this lab...
Lab 7.1.9a Introduction to Fluke Network Inspector
...
Lab 7. 1.9a Introduction to Fluke Network Inspector
Objective
This lab is a tutorial demonstrating how to use the Fluke Networks ... available?
_______________________________________________
h. Which interfaces are up?
____________________________________________________
10 - 12 CCNA 1: Networking Basics v 3.0 - Lab 7. 1.9a ... 3.0 - Lab 7. 1.9a Copyright 2003,...
Lab 7.1.9b Introduction to Fluke Protocol Inspector
... Basics v 3.0 - Lab 7. 1.9b Copyright 2003, Cisco Systems, Inc.
16 - 18 CCNA 1: Networking Basics v 3.0 - Lab 7. 1.9b Copyright 2003, Cisco Systems, Inc.
17 - 18 CCNA 1: ... Basics v 3.0 - Lab 7. 1.9b Copyright 2003, Cisco Systems, Inc.
18 - 18 CCNA 1: Networking Basics v 3.0 - Lab 7. 1.9b Copyright 2003, Cisco Systems, Inc.
Step 1 Configure th...
Lab 7.2.2 Configuring RIP
...
BHM(config-router)#network 172 . 17. 0.0
BHM(config-router)#network 172 .18.0.0
BHM(config-router)#exit
BHM(config)#exit
2 - 5 CCNA 2: Routers and Routing Basics v 3.0 - Lab 7. 2.2 Copyright 2003, ... Establishing a HyperTerminal session lab.
Note: Go to the erase and reload instructions at the end of this lab. Perform those steps on all
routers in this lab assignment before...
Lab 7.2.4 Selecting the Root Bridge
... 1 - 6 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 7. 2.4 Copyright 2003, Cisco Systems, Inc.
Lab 7. 2.4 Selecting the Root Bridge
Objective
• Create a basic switch ... Switching Basics and Intermediate Routing v 3.0 - Lab 7. 2.4 Copyright 2003, Cisco Systems, Inc.
Erasing and Reloading the Switch
For the majority of the labs in CCNA 3 and CCNA 4 it is...
Tài liệu Lab 7.2.4 Selecting the Root Bridge docx
... this configuration,
refer to the Basic Switch Configuration lab.
1 - 5 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 7. 2.4 Copyright 2003, Cisco Systems, Inc.
Step 2 Configure ...
Lab 7. 2.4 Selecting the Root Bridge
Objective
• Create a basic switch configuration and verify it. ...
______________________________________
2 - 5 CCNA 3: Switching Basics and...
Tài liệu 1 - 4 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 7.2.6 Copyright 2003, Cisco Systems, Inc. Lab 7.2.6 Spanning Tree Recalculation docx
... 1 - 4 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 7. 2.6 Copyright 2003, Cisco Systems, Inc.
Lab 7. 2.6 Spanning Tree Recalculation
Objective
• Create a basic switch ... of each switch.
Switch A Port # Switch B
1
2
3
4
5
6
7
8
9
10
11
12
3 - 4 CCNA 3: Switching Basics and Intermediate Routing v 3.0 - Lab 7. 2.6 Copyright 2003, Cisco Systems, Inc.
S...
Tài liệu Lab 7.2.6 Troubleshooting RIP ppt
... interface
identifiers to be used based on the equipment in the lab. The configuration output used in this lab is
produced from 172 1 series routers. Any other router used may produce a slightly ... Establishing a HyperTerminal session lab.
Note: Go to the erase and reload instructions at the end of this lab. Perform those steps on all
routers in this lab assignment before continuin...