FX Series Programmable Controllers jy992d84601b
FX Series Programmable Controllers y992d69901c
... more Use FX 2N -232IF Not supported. FX 2N + FX 2N -CNV-BD FX, FX 2C FX 2N + FX 2N -232-BD FX 0N -232ADP RS232C FX 2N + FX 2N -CNV-BD FX 1N + FX 1N -CNV-BD FX 1S + FX 1N -CNV-BD FX 0N , FX 2NC FX 2N ... 5 FX, FX 2C FX 0N -485ADP FX 2 , FX 2C Computer FX- 485ADP FX 2N + FX 2N -485-BD, FX 1S + FX 1N -485-BD, FX 1N + FX 1N -485-BD A...
Ngày tải lên: 23/04/2014, 08:14
FX Series Programmable Controllers jy992d48901a
... block(s) + FX 0N -16NT block(s)) should be no more than 2 blocks. Note: The total number of input/output points should be 128 points or less. FX 0N -40MR FX 0N -16NT FX 0N -16NTFX 0N -8EX FX 0N -8EYR "n" "m" Inputs: ... 2 Station 1 (FX 0N ) Twisted pair cable 16-point output unit 16-point input unit A Series PC C P U FX 0N - 16NT FX 0N -40MR Power supply...
Ngày tải lên: 23/04/2014, 08:14
FX Series Programmable Controllers jy992d49001b
... control of the FX 0N -3A; by use of the TO/FROM applied instructions in the FX 0N PC. Communications between the FX 0N PC and FX 0N -3A are protected by opto-coupler. • The FX 0N -3A occupies ... the FX 0N -3A special function block and should be read and understood before attempting to install or use the unit. Further information can be found in the FX PROGRAMMING MANUAL and...
Ngày tải lên: 23/04/2014, 08:14
FX Series Programmable Controllers jy992d53501a
... No. 10 Station No. 1Station No. 0 FX series PC FX series PC A series PCFX series PC A series PC 485PC-IF Computer RS-485 RS-232C Notes The FX series PCs and A series PCs are shown separately in ... A series PC, see the A series manual. M8002 The following instructions can be used to set the station number of station 0 in the above system. Computer 485PC-IF FX series...
Ngày tải lên: 23/04/2014, 08:14
FX Series Programmable Controllers jy992d65301d
... (DIR) Forward Reverse OFF ON OFF ON 5 FX- 1PG /FX 2N -1PG PULSE GENERATOR UNIT BFM LIST 5-4 FX- 1PG /FX 2N -1PG PULSE GENERATOR UNIT USER'S MANUAL FX- 1PG /FX 2N -1PG PULSE GENERATOR UNIT USER'S ... start command is not accepted. 5 FX- 1PG /FX 2N -1PG PULSE GENERATOR UNIT BFM LIST 5-15 MEMO 5 FX- 1PG /FX 2N -1PG PULSE GENERATOR UNIT BFM LIST 5-16 MEMO 5 FX- 1PG /FX 2N -1...
Ngày tải lên: 23/04/2014, 08:14
FX Series Programmable Controllers jy992d71801b
... resistor Shielded twisted pair cable Remote device station FX 0N /FX 2N /FX 2NC Series PC + FX 2N -32CCL Remote device station FX 0N /FX 2N /FX 2NC Series PC + FX 2N -32CCL Remote I/O station Remote device ... units Up to 26 units Up to 42 units 64 units in all A1SJ61QBT11 AJ61QBT11 FX PC FX 0N /FX 2N /FX 2NC Series + FX 2N -32CCL FX 2N -32CCL CC-Link In...
Ngày tải lên: 23/04/2014, 08:14
FX Series Programmable Controllers jy992d73701b
... unit FX 2N -16LNK-M MELSEC-I/O LINK REMOTE I/O SYSTEM MASTER BLOCK Connection and Wiring 3 3-5 FX 0N /FX 2N Series DC power supply type FX 2NC Series (DC power supply type) When an FX 2NC Series ... FX 0N /FX 2N /FX 2NC Series *2 The number of I/O points include a basic unit, extension units/blocks, special extension units/blocks and remote I/O units. FX 2NC -CNV...
Ngày tải lên: 23/04/2014, 08:14
FX Series Programmable Controllers
... unit.) FX Series Programming Manual II JY992D88101 Describes instructions in FX 1S /FX 1N /FX 2N /FX 2NC Series. X4 L N X0 X2 COM X5X1 X3 COM Y3Y0 Y2Y1 COM2COM1 24+ COM3COM0 POWER ERROR FX1 S-10MR OUT 0123 RUN 0123 54 10MR - ... unit.) FX Series Programming Manual II JY992D88101 Describes instructions in FX 1S /FX 1N /FX 2N /FX 2NC Series. X4 L N X0 X2 COM X...
Ngày tải lên: 23/04/2014, 08:14