TRANSFORMER AND INDUCTOR DESIGN HANDBOOK - COLONELWM t MCLYMAN

... Voltage Transformer (CVT) Chapter 12 Three-Phase Transformer Design Chapter 13 Flyback Converter, Transformer Design Chapter 14 Forward Converter, Transformer Design, and Output Inductor Design Chapter ... 3 Magnetic Cores Chapter 4 Window Utilization, Magnet Wire, and Insulation Chapter 5 Transformer Design Trade-Offs Chapter 6 Transformer- Inductor...

Ngày tải lên: 22/04/2014, 16:52

... acid. Ethyl acetate, n-butyl acetate, iso-butyl acetate, glycerol trinitrate, pentaerythritol tetranitrate (PETN), glycol dini- trate, and cellulose nitrate are examples of such reactions. Ester ... salicylate, methyl anthranilate, diethyl-phthalate, dibutyl-phthalate, and di-2-ethylhexyl-phthalate. Unsaturated vinyl esters for use in polymerization reactions are made by the esterificatio...

Ngày tải lên: 02/04/2014, 16:23

... the author claims that the book is written with a student-oriented approach. Yet, the students should know that the ability to understand the solution to the problems is important but understanding ... systems, unit pulse response and transfer functions, stability theory, and the Jury–Marden test are treated in this chapter. The amount of material on the time-domain analysis of discrete-t...

Ngày tải lên: 13/09/2012, 10:21

... press); the static friction coefficient is the design parameter to be used. On the other hand, the pertinent design param- eters are the dynamic friction coefficient and its change with temperature when ... demands of the problem at hand. Where appropriate, the resulting formulas are collected at the end of each chapter so that those not interested in their derivation may turn directly to t...

Ngày tải lên: 20/10/2012, 09:58

... budget memory; low-cost RF components that can provide acceptable performance at 1900/2100 MHz; and high-density battery technologies. Introduction xxi Bandwidth Quantity and Quality Over the next ... included pro- grams on AMPS/ETACS handset, base station, and network design in the early to mid-1980s; programs on GSM handset, base station, and network design from the late 1980s...

Ngày tải lên: 20/08/2013, 14:10

... fabri- cate resistors in the form of thick-film and later thin-film depositions on ceramic substrates instead of using printed circuit boards. These filters did not use induc- tors and transformers and ... from the analog signal x (t) and deliver an output signal y d (t) . It is appropriate to compare these two circuit configurations and determine whether it is possible to get the outp...

Ngày tải lên: 29/09/2013, 21:20

... Fundamentals 2 extends the ‘‘at sat- uration’’ table down to Ϫ80ЊF. The table indicates that there is a correspondence between satura- tion temperature and absolute pressure. Thus, the normal (sea-level) boiling ... pressurized to above the saturation pressure correspond- ing to the water temperature, to prevent the water from flashing into steam. Heat exchangers are used to provide lower-te...

Ngày tải lên: 17/10/2013, 22:15

... proposed in the design pattern literature: ! Abstract Factory The Abstract Factory design pattern allows the creation of related dependent objects without the specification of their concrete classes. ... retrieval and do not participate in transactions, and the objects that manipulate data and can participate in transactions. The DAL is an example of using the Adapter struct...

Ngày tải lên: 19/10/2013, 02:15

... Design Pattern in the ATM System: State +Handle() State +Handle() ConcreteStateA +Handle() ConcreteStateB +Request() Context One behavioral design pattern used in the logical design of the ... design pattern allows a many-to-many relationship between ATM machines that generate the transactions and the transaction processing systems that post them into the ATM user accounts....

Ngày tải lên: 19/10/2013, 02:15