... 9 0 Printed on acid-free paper Library of Congress Cataloging-in-Publication Data Wilson, H .B. Advanced < /b> mathematics < /b> and < /b> mechanics < /b> applications < /b> using < /b> MATLAB < /b> / Howard < /b> B. Wilson, Louis H. Turcotte, ... Edition Advanced < /b> Mathematics < /b> and < /b> Mechanics < /b> Applications < /b> Using < /b> Howard < /b> B. Wilson...
Ngày tải lên: 08/04/2014, 09:57
... additional MATLAB < /b> commands to get one started on MATLAB.< /b> Detailed descriptions and < /b> usages of the commands can be obtained from the MATLAB < /b> help facility or from MATLAB < /b> manuals. Table 1.2 Some Basic ... into the MATLAB < /b> command window the statement ex1_4 and < /b> observe the results. The following results will be obtained: ra = -1 < /b>...
Ngày tải lên: 23/10/2013, 16:15
Electronics and Circuit Analysis Using MATLAB
... NON-INVERTING CONFIGURATION 11.4 EFFECT OF FINITE OPEN-LOOP GAIN 11.5 FREQUENCY RESPONSE OF OP AMPS 11.6 SLEW RATE AND < /b> FULL-POWER BANDWIDTH 11.7 COMMON-MODE REJECTION SELECTED BIBLIOGRAPHY ... yt yt yt yt n () () () . . () = 1 2 and < /b> A, B, C , and < /b> D are matrices determined by constants of a system. For example, consider...
Ngày tải lên: 27/10/2013, 23:15
Electronics and Circuit Analysis Using MATLAB P3
... allows commands to be viewed as they execute. The echo can be enabled or disabled. echo on - < /b> enables the echoing of commands echo off - < /b> disables the echoing of commands echo - < /b> by itself toggles ... Keyboard The keyboard command invokes the keyboard as an m-file. When the word keyboard is placed in an m-file, execution of the m-file stops when the word k...
Ngày tải lên: 27/10/2013, 23:15
Electronics and Circuit Analysis Using MATLAB P2
... commands can be used to select and < /b> clear the windows: shg - < /b> shows graph window any key - < /b> brings back command window clc - < /b> clears command window clg - < /b> clears graph window home - < /b> home command ... PLOTTING COMMANDS 2.1 GRAPH FUNCTIONS MATLAB < /b> has built-in functions that allow one to generate bar charts, x-y, polar, con...
Ngày tải lên: 27/10/2013, 23:15
Electronics and Circuit Analysis Using MATLAB P6
... = (5+12*j)*I(1); Vbn = (3+4*j)*I(2); Vcn = ( 5-1 < /b> 2*j)*I(3); Van_abs = abs(Van); Van_ang = angle(Van)*180/pi; Vbn_abs = abs(Vbn); Vbn_ang = angle(Vbn)*180/pi; Vcn_abs = abs(Vcn); Vcn_ang ... (6.33) +- < /b> +- < /b> - + 110 0 o V 110 -1 < /b> 20 o V 110 120 o V 1 + j1 Ohms 1 - < /b> j2 Ohms 1 - < /b> j0.5 Ohms 5 + j12 Ohms 3 + j4 Ohms 5 - < /b> j12 Ohms...
Ngày tải lên: 06/11/2013, 09:15
Electronics and Circuit Analysis Using MATLAB P5
... yt yt yt yt n () () () . . () = 1 2 and < /b> A, B, C , and < /b> D are matrices determined by constants of a system. For example, consider a single-input and < /b> a single-output system described by the differential ... system of ordinary differential equations using < /b> second- and < /b> third-order Runge- Kutta formulas; the ode45 functi...
Ngày tải lên: 06/11/2013, 09:15
Electronics and Circuit Analysis Using MATLAB P4
... matrix Y and < /b> the current vector I of % matrix equation Y V = I Y = [-4 < /b> .4 0.125 -0 < /b> .125 4.9 0; -0 < /b> .1 0 -0 < /b> .2 0.55 -0 < /b> .25; 0 -0 < /b> .125 0.325 -0 < /b> .2 0; 1 0 -0 < /b> .6 -0 < /b> .4 0; 0 0 0 0 1]; I = [0 0 5 -4 < /b> 0 24]'; ... matrix Y and < /b> current vector I % Y is the admittance matrix and < /b> I is the cu...
Ngày tải lên: 06/11/2013, 09:15
Tài liệu Electronics and Circuit Analysis Using MATLAB P12 pdf
... ββ FF +≅ 1 , then III CFBFCBO =+ ββ (12.43) so I I I B C F CBO =− β (12.44) The loop equation of the base-emitter circuit of Figure 12.6 (b) gives () VV IR RII BB BE B BB E B C −= + + ... α I C I E I R I F R I F R I F V BC V BE I B α + + - < /b> - Figure 12.2 Ebers-Moll Static Model for an NPN transistor (Injection Version) The voltages at the bas...
Ngày tải lên: 13/12/2013, 01:15
Tài liệu Electronics and Circuit Analysis Using MATLAB P11 doc
... oscillators, and < /b> flip-flops. In this chapter, the basic properties of op amps will be discussed. The non-ideal characteristics of the op amp will be illustrated, whenever possi- ble, with example problems ... the relationship between the rated output voltage and < /b> the full-power bandwidth. Example 11.6 The LM 741 op amp has a slew rate of 0.5 V/µs. Plot the full-power b...
Ngày tải lên: 13/12/2013, 01:15