The Fundamentals of Interior Design

... issues connected to interior design. The Fundamentals of Interior Design provides a thorough introduction to the key elements of interior design and the ideas that underpin them. From researching ... Basics Interior Design: Retail design Basics Interior Design: Exhibition design Basics Interior Design: Residential design Basics Interior Desi...

Ngày tải lên: 17/03/2014, 18:02

... there is another range of tints caused by the effect of electric light. And not only do you have the colour of the skin to consider, but also the colour of your model’s clothes and of the background ... deep azure space of the sky. Make the most of the decorative values of the plant shapes and the animal’s markings – don’t try to be too realistic. The wh...

Ngày tải lên: 13/09/2012, 14:19

... alert("hey there! "); } Calling a Function Calling a function is very simple. You type out the name, and then parentheses and the func- tion will be executed. The parentheses tell the browser ... because they are executed at runtime rather than waiting to be called. Anonymous functions perform very well in the browser because there is no reference to them in another p...

Ngày tải lên: 03/01/2013, 15:51

... fourth example ([), I’ve positioned the center of the gradient at 80 percent of the width and 50 percent of the height of the box and set the limit of the radius to the nearest (right) side. Again, ... limit of the radius to the farthest side of the box, but this time, I set the center point as the center of the left side. In WebKit, I defined t...

Ngày tải lên: 20/09/2013, 09:09

... the code. This value depends on a. type of the joint b. type of stress experienced by the joint c. a load factor K defined as the ratio of the minimum stress to the maximum stress. When the ... where w denotes the leg size of the fillet weld measured in centimeter. The design is found to be safe if the maximum value of the fluctuating stress is found...

Ngày tải lên: 18/10/2013, 09:15

... rotating. The basic nature of friction again suggests that the driven pulley opposes the motion of the belt. The directions of friction on the belt and the driven pulley are shown the figure. The ... is the mass of the belt of unit length, m = btρ (13.1.4) where, b is the width, t is the thickness and ρ is the density of the belt material....

Ngày tải lên: 25/10/2013, 12:15

... and join the ends together. The fixing of the joint must be done properly because the belt normally gets snapped from the improper joints. The best way is to use a cemented belt from the factory ... are specified on the following parameters Material The decision of the material to be used depends on the type of service. No. of ply and Thickness Ply is...

Ngày tải lên: 25/10/2013, 12:15

... indicated in the figure. The pitch line, which is also marked as N-A, is the neutral axis of the belt section. The design calculations for V- belt drives are based on the pitch line or the neutral ... that section for which the required power transmission falls in the lower side of the given range. Another restriction of choice of belt section arises from...

Ngày tải lên: 29/10/2013, 19:15

... :Minimumfilmthickness positionθ The above design parameters are defined in the Fig. 14.1.6. The pressure profile shown is only for the positive part of the bearing where the converging zone is present. ... At the end of this lesson, the students should be able to understand: Types of bearings Comparison of bearing friction characteristics Basics...

Ngày tải lên: 29/10/2013, 19:15

... safe design approach at every stage of the design is needed. Use of factor of safety in designing the elements is to optimize the design to avoid over- design for reliability. 1.1.7 Summary of ... Lesson The lesson essentially discusses the basic concept of design in general leading to the concept of machine design which involves primarily designing...

Ngày tải lên: 17/12/2013, 11:15