FUNDAMENTALSof Game DesignSECOND EDITIONErnest Adams FUNDAMENTALS OF GAME DESIGN, SECOND doc

... to Fundamentals of Game Design, Second Edition—an updated version of the original Fundamentals of Game Design, which was itself based upon an earlier book called Andrew Rollings and Ernest Adams ... versions. ptg7947181 The Elements of Game Design Part One of Fundamentals of Game Design examines the essential principles of designing video games. The first...

Ngày tải lên: 14/03/2014, 21:20

... any section a compressive stress of π 2 4F d and a bending stress of My I are produced. Here d is the diameter of the circular bar, I the second moment of area and the moment is PL 2 ... section X-X, Q the first moment of area, I the moment of inertia, t the width at which transverse shear is calculated, J the polar moment of inertia and r the radius of the circu...

Ngày tải lên: 25/12/2013, 23:18

... torque of 5 KN-m. The material has a yield point of 350 MPa. Find the required diameter using (a) Maximum shear stress theory (b) Maximum distortion energy theory Take a factor of safety of 2.5. ... Summary of this Lesson Different types of loading and criterion for design of machine parts subjected to static loading based on different failure theories have been demonstra...

Ngày tải lên: 25/12/2013, 23:18

... change in length of 0.2 mm. Determine the maximum stress developed in the bar. Take E= 200 GPa. 3.2.4.1F A.1: Total change in length of the bar is made up of three components ... 3.2.1.4F- Variation of theoretical stress concentration factor with r/d of a stepped shaft for different values of D/d subjected to uni-axial loading (R...

Ngày tải lên: 25/12/2013, 23:18

... However, in the presence of notches and cracks determination of total strain is difficult. 3.4.1.2F- Plots of strain amplitude vs number of stress reversals for failure. ... 4) Mechanical engineering design by Joseph E. Shigley, McGraw Hill, 1986. 5) Fundamentals of machine component design, 3 rd edition, by Robert C. Juvinall and Kurt M. Marshe...

Ngày tải lên: 25/12/2013, 23:18

... Bending of a knuckle pin 4. Failure of rod eye in shear: ( ) 21 ddtP−τ= 5. Failure of rod eye in crushing: 1c dt Pσ= 6. Failure of rod eye in tension: ( ) 21t ddt P−σ= 7. Failure of ... tensile or compressive forces along the axes of the rods. Examples of cotter joint connections are: connection of piston rod to the crosshead of a steam engine, valve rod and...

Ngày tải lên: 25/12/2013, 23:18

... (8.1.1) Where, M : Bending moment at the point of interest d o : Outer diameter of the shaft k : Ratio of inner to outer diameters of the shaft ( k = 0 for a solid shaft because ... Kamalesh, Design of Machine Elements, Prentice Hall of India, New Delhi, 2003. Version 2 ME , IIT Kharagpur Module 8 Design of Shaft...

Ngày tải lên: 23/01/2014, 04:20

... junctions we ld weld 9.2.2.4F- Method of construction of multilayered cylinder 3. Autofrettage In some applications of thick cylinders such as gun barrels no inelastic deformation ... find the radial displacements of the cylinder walls at the contact we consider that ( r u1 rE θθ ) ε == σ−νσ. This gives the radial displacement of the inner wall of the...

Ngày tải lên: 27/01/2014, 14:20

... necessary thickness of the shell plates of 2.5m diameter boiler with the internal pressure of 1MPa. The material is mild steel with a tensile strength of 500MPa. Assuming an efficiency of the longitudinal ... cylinders as well as the gradient across the wall of a single cylinder. 9.3.3 Summary of this Lesson The lesson initially discusses the application of different...

Ngày tải lên: 27/01/2014, 14:20

... centers of rivets in adjacent rows of zigzag riveted joint. (usual symbol d p ) d) Margin or marginal pitch: This is the distance between the centre of the rivet hole to the nearest edge of the ... know: • Basic types of riveted joints. • Different important design parameters of a riveted joint. • Uses of riveted joints. 1. Rivets as permanent joints: Often small...

Ngày tải lên: 27/01/2014, 14:20