Cisco IOS Configuration Fundamentals Command Reference ppt

... Configuration Fundamentals Configuration Guide • Cisco IOS Configuration Fundamentals Command Reference Autoinstall, Setup, Cisco IOS command- line interface (CLI), Cisco IOS file system (IFS), Cisco ... Cisco IOS Software Documentation Documentation Organization xxvi Cisco IOS Configuration Fundamentals Command Reference April 2010 • Cisco IO...

Ngày tải lên: 11/03/2014, 21:20

... number of chans 1-92 Cisco MGX 8220 Command Reference, Release 4.1 copyports copyports The copyports command copies a port configuration to one or more ports. The purpose of this command is to create ... 1-255 1-96 Cisco MGX 8220 Command Reference, Release 4.1 delbstunport delbstunport This command deletes a BSTUN port. For more information about using BSTUN and its commands...

Ngày tải lên: 24/01/2014, 13:20

... Overview of Cisco IOS XR 9 Cisco IOS XR Platforms 13 Cisco CRS-1 Carrier Routing System 13 Cisco XR 12000 Series 14 Cisco ASR 9000 Series 14 Chapter 2 Cisco IOS XR Infrastructure 17 Cisco IOS XR Kernel ... Authentication in IOS XR IS-IS 243 Chapter 8 Implementing BGP in Cisco IOS XR 247 Cisco IOS XR BGP Architectural Overview 247 Cisco IOS XR BGP Hierarchic...

Ngày tải lên: 17/03/2014, 03:20

... Chapter4 Introduction to the Cisco IOS The Cisco Router User Interface Cisco Internetwork Operation System (IOS) 是 Cisco 的 routers 和 switches 的内核 Cisco Router IOS IOS 的一些功能: 1.运载网络协议和功能 ... 当启动 1 个 router 的时候,大致将分为以下几个阶段: 1.开机自检(power-on self-test,POST) 2.如果 1 正常, 如果 IOS 存在的话,将从它的闪存(flash memory)查找和...

Ngày tải lên: 10/12/2013, 16:15

... particular IOS. After you have exhausted all other debugging possibilities, check the Cisco web site for bugs in your IOS. There are IOS versions in which access lists do not function correctly. The Cisco ... complex examples of using Cisco IOS Access lists Page 158 Prefix lists are viewed with the show ip prefix-list command. Similar to the show access-list command, when...

Ngày tải lên: 11/12/2013, 00:15

... are two ways to set local preference: • Using the bgp default local-preference Command • Using a Route Map to Set Local Preference Using the bgp default local-preference Command The following configurations ... connection to the WAN. Underlying and integrating all Cisco products is the Cisco Internetworking OperatingSystem (Cisco IOS) software. The Cisco IOS software enables disp...

Ngày tải lên: 24/01/2014, 19:20

... • The Cisco IOS software supports two EXEC command modes: user and privileged. © 2002, Cisco Systems, Inc. All rights reserved. 2 Operating and Configuring Cisco IOS Devices Module 1 © 2002, Cisco ... that are external to the device. • Cisco IOS software uses a CLI as its traditional console environment. While Cisco IOS software is a core technology, Cisco IOS...

Ngày tải lên: 08/07/2013, 01:27

... reserved. 2 Managing Cisco IOS Devices © 2002, Cisco Systems, Inc. All rights reserved. ICND v2.0—2-20 Summary (Cont.) • You use the Cisco IOS software copy commands to move configurations from ... on Cisco devices © 2002, Cisco Systems, Inc. All rights reserved. ICND v2.0—2-4 Cisco IOS File System and Devices © 2002, Cisco Systems, Inc. All rights reserved. ICND v2.0—2-5...

Ngày tải lên: 08/07/2013, 01:27

... several scenarios. The format of the nat and global commands as used in Dynamic NAT is shown below: ciscoasa(config)# nat (internal_interface_name) “nat-id” “internal network IP subnet” ciscoasa(config)# ... binds the nat command with the global command. Its importance will be clearer in our next scenarios. Also note the names “inside” and “outside” used in the nat and global comm...

Ngày tải lên: 17/09/2013, 15:12