Diploma in Mechanical Engineering (Production & Automobile) doc

Diploma in Mechanical Engineering (Production & Automobile) doc

Diploma in Mechanical Engineering (Production & Automobile) doc

... 2008) Delhi Road, Moradabad (U.P) Study & Evaluation Scheme of Diploma in Engineering (Mechanical) SUMMARY Programme : Diploma in Engineering (Mechanical) (a) Production (b) Automobile ... Mechanism:- Introduction, Kinetic link. Types of link, Difference between machine and structure, kinetic pairs, types of constrained motions, kinetic chains, types of joints in...

Ngày tải lên: 09/03/2014, 00:20

128 451 0
Higher National Diploma in Mechanical Engineering 2012 ppt

Higher National Diploma in Mechanical Engineering 2012 ppt

... Electronic Engineering and Instrumentation and Control. Derek worked in the telecommunication industry prior to becoming a lecturer in engineering. He gained a HND in Electrical & Electronic Engineering ... understanding of scientific principles underpinning mechanical systems. K3 Apply, question and relate mechanical engineering principles to produce solutions to...

Ngày tải lên: 18/03/2014, 02:20

31 388 1
Tài liệu PROBLEMS AND SOLUTIONS IN MECHANICAL ENGINEERING doc

Tài liệu PROBLEMS AND SOLUTIONS IN MECHANICAL ENGINEERING doc

... begins a new cycle. Applying the first law: in out in out final initial ()()( ) f QQ WW mh h −+−= − && && & in out out 0, 0 0 QQW=== && & in 1 4 (). f Wmhh =− & & However, ... Work ratio is defined as the ratio of net plant output to the gross (turbine) output. Work ratio = out in 1 out 1 c WW WW WW − = && & & && Q. 21:...

Ngày tải lên: 22/02/2014, 09:20

529 514 0
Tài liệu Handbook of Mechanical Engineering Calculations P7 docx

Tài liệu Handbook of Mechanical Engineering Calculations P7 docx

... PUMPING SYSTEMS PUMPS AND PUMPING SYSTEMS 7.61 FIGURE 39 Constant-head curves for turbine only. (Chemical Engineering. ) FIGURE 38 Constant-head curves for turbine duty. (Chemical Engineering. ) In ... PUMPING SYSTEMS 7.60 PLANT AND FACILITIES ENGINEERING FIGURE 36 Constant-speed curves for turbine duty. (Chemi- cal Engineering. ) FIGURE 37 Constant-speed curves for turbine duty. (Chem...

Ngày tải lên: 17/12/2013, 11:15

86 917 14
Tài liệu Handbook of Mechanical Engineering Calculations P8 doc

Tài liệu Handbook of Mechanical Engineering Calculations P8 doc

... resistance. Data shown in Table 38 are also presented in graphical form in some engineering data. 2. Select a suitable piping material Refer to piping engineering data to determine the corrosion resistance ... Consultant, DuPont Engineering (Table 44), as reported in Chemical Engineering Magazine. The economic study in Step 3 is the work of Max Kurtz, P.E. FRICTION LOSS IN...

Ngày tải lên: 17/12/2013, 11:15

136 561 0
Tài liệu Handbook of Mechanical Engineering Calculations P11 doc

Tài liệu Handbook of Mechanical Engineering Calculations P11 doc

... liquid heating, gas and air heating, oven warming, deicing, humidifying, plastics heating, pipe heating, etc. Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineeringlibrary.com) Copyright ... FACILITIES ENGINEERING FIGURE 7 Heat losses from melting pots. (General Electric Co.) TABLE 4 Two Methods for Determining Wattage for Heating Buildings Electrically* Downloa...

Ngày tải lên: 17/12/2013, 11:15

86 620 0
Tài liệu Fiber in Broadcast and Production Facilities docx

Tài liệu Fiber in Broadcast and Production Facilities docx

... that when working with fiber, relying on factory- terminated cables offers several advantages over field termination, including performance and savings in labor, material costs and installation ... such as following a 1.5-inch bend radius policy, guarding against excessive cable pile-up, troughing horizontal runs, implementing vertical cable protection and providing for expanding sla...

Ngày tải lên: 21/12/2013, 07:17

12 414 0
Tài liệu Mechanical Engineering Handbook P2 docx

Tài liệu Mechanical Engineering Handbook P2 docx

... particles). 3.The motion is in a nonaccelerating reference frame. FIGURE 1.3.6Motion of a particle in cylindrical coordinates. FIGURE 1.3.7Relative motion using translating coordinates. rrr vvv aaa BABA BABA BABA =+ =+ =+ Fa=m Mechanics ... particle that moves in circular motion the equations simplify to (1.3.11) Motion of a Particle in Cylindrical Coordinates Cylindrical coordinates...

Ngày tải lên: 23/12/2013, 00:15

10 454 0
Tài liệu Mechanical Engineering Handbook P1 doc

Tài liệu Mechanical Engineering Handbook P1 doc

... learn something new, but what is needed at the moment is not at their fingertips. This chapter may help the reader in such a situation. Within the constraints of a single book on mechanical engineering, ... following procedure is recommended. 1.Determine the support reactions if the section used in the analysis includes the joints supported. FIGURE 1.2.23Method of joints in analyzing...

Ngày tải lên: 23/12/2013, 00:15

40 433 1
Tài liệu Handbook of Mechanical Engineering Calculations P13 doc

Tài liệu Handbook of Mechanical Engineering Calculations P13 doc

... to maintain the contents of the tank in a completely mixed state. Al- though there are numerous ways to accomplish continuous mixing, mechanical mixing will be used here. In mechanical mixing, ... trough. During the backwash cycle, wastewater is filtered continuously through the cells not being backwashed. Downloaded from Digital Engineering Library @ McGraw-Hill (www.digitalengineer...

Ngày tải lên: 25/12/2013, 23:18

56 569 0
w