Fundamentals of Programming doc

... context of software development, including computer systems and tools. ©2013 Richard L. Halterman Draft date: January 27, 2013 1.1. SOFTWARE 2 1.1 Software A computer program is an example of computer ... write software. There are no substitutes for sound logical thinking, creativity, common sense, and, of course, programming experience. 1.3 Learning Programming with C++ Bjarne Stro...

Ngày tải lên: 08/03/2014, 11:20

... pseudocode. www.it-ebooks.info 92 Start Here! Fundamentals of .NET Programming Pseudocode Pseudocode uses English-like words to describe computer algorithms without relying on any particular programming ... this version uses the keyword class instead of struct. www.it-ebooks.info 78 Start Here! Fundamentals of .NET Programming After you create a variable of type Address,...

Ngày tải lên: 16/02/2014, 06:20

... WHITE PAPER Fundamentals of Ethernet Technology Fundamentals of Ethernet Technology This white paper provides a brief tutorial on Ethernet – a family of standards that defines ... topologies and types of cabling. New high-speed offerings support not only data, but voice and video as well. • Highly reliable. It’s a well-tested technology. Fundamentals of Ethernet Technology...

Ngày tải lên: 10/12/2013, 02:15

... display) Fundamentals of Digital Electronics 10-6 © National Instruments Corporation Lab 10 Seven-Segment Digital Displays Notes © National Instruments Corporation 11-1 Fundamentals of Digital ... period of time. This timing period is the reciprocal of the Baud rate, the frequency of data transmission measured in bits per second. For example, a 300 Baud data rate has a timing...

Ngày tải lên: 13/12/2013, 01:15

Ngày tải lên: 20/12/2013, 17:15

... cost/performance trade-offs than those using current costs. The caption of Figure 1.3 discusses some of the long-term trends in DRAM cost. FIGURE 1.3 Prices of four generations of DRAMs over time ... instruction formats, and a large number of registers. Figure 2.30 shows the ratio of the number of instructions executed, the ratio of CPIs, and the ratio of performance measu...

Ngày tải lên: 22/12/2013, 10:16

... At the end of this lesson, the student should be able to understand • Elements of force system at a beam section. • Superposition of axial and bending stresses. • Transformation of plane stresses; ... section X-X, Q the first moment of area, I the moment of inertia, t the width at which transverse shear is calculated, J the polar moment of inertia and r the radius of...

Ngày tải lên: 25/12/2013, 23:18

... torque of 5 KN-m. The material has a yield point of 350 MPa. Find the required diameter using (a) Maximum shear stress theory (b) Maximum distortion energy theory Take a factor of safety of 2.5. ... Summary of this Lesson Different types of loading and criterion for design of machine parts subjected to static loading based on different failure theories have been demonstra...

Ngày tải lên: 25/12/2013, 23:18

... change in length of 0.2 mm. Determine the maximum stress developed in the bar. Take E= 200 GPa. 3.2.4.1F A.1: Total change in length of the bar is made up of three components ... 3.2.1.4F- Variation of theoretical stress concentration factor with r/d of a stepped shaft for different values of D/d subjected to uni-axial loading (R...

Ngày tải lên: 25/12/2013, 23:18

... However, in the presence of notches and cracks determination of total strain is difficult. 3.4.1.2F- Plots of strain amplitude vs number of stress reversals for failure. ... At the end of this lesson, the students should be able to understand • Design of components subjected to low cycle fatigue; concept and necessary formulations. • Design of...

Ngày tải lên: 25/12/2013, 23:18