Tài liệu Fundamentals of Linux LEU-118 Student Guide ppt

... any aspects of this exercise. • Conclusions 9 Have students articulate any conclusions they reached as a result of this exercise experience. • Applications 9 Explore with students how ... Interpretations 9 Ask students to interpret what they observed during any aspects of this exercise. • Conclusions 9 Have students articulate any conclusions they reached as a resu...

Ngày tải lên: 18/02/2014, 21:20

... Systems, Inc. Lab 9.2.1: Installation of Linux Estimated Time: 50 minutes Objective • Install the Red Hat distribution of Linux • Configure the Linux settings as needed • Create a boot ... distributions of Linux. The Linux kernel remains the same among these distributions but the different versions appeal to different markets. This lab will use the Red Hat distribut...

Ngày tải lên: 11/12/2013, 15:15

... display) Fundamentals of Digital Electronics 10-6 © National Instruments Corporation Lab 10 Seven-Segment Digital Displays Notes © National Instruments Corporation 11-1 Fundamentals of Digital ... period of time. This timing period is the reciprocal of the Baud rate, the frequency of data transmission measured in bits per second. For example, a 300 Baud data rate has a timing...

Ngày tải lên: 13/12/2013, 01:15

... 458-460 of free space, m 0 , 458 relative, m r , 458 Phase asymptotes of complex poles, 279-282 inverted forms, 272 of real pole, 266-268 of real zero, 269 of RHP zero, 270 Phase control of resonant ... currents, table of, 609 of near-ideal rectifier waveforms, 604-609 Rotation of three-terminal cell, 141-142 Saturation of inductors, 462, 465-466 of magnetic materials, 45...

Ngày tải lên: 13/12/2013, 01:15

... (1 of 2) [25/04/2002 16:42:07] Fundamentals of Power Electronics http://ece-www.colorado.edu/~pwrelect/book/copies.html (2 of 2) [25/04/2002 16:42:07] Fundamentals of Power Electronics Table of ... http://ece-www.colorado.edu/~pwrelect/book/SecEd.html (6 of 6) [25/04/2002 16:42:05] Fundamentals of Power Electronics Fundamentals of Power Electronics Second Edition Up...

Ngày tải lên: 13/12/2013, 01:15

... the memory of a computer. Each variable has a type that indicates the kind of value that will be stored in that variable. You can use any of the types shown earlier in Table 2.3 of Chapter ... Fundamentals of Transact-SQL In this section, you'll learn some of the essential programming constructs available in T- SQL. ... character (@) before the start of the variable na...

Ngày tải lên: 14/12/2013, 13:15

... Instructional Objectives At the end of this lesson, the students should have the knowledge of • Basic concept of design in general. • Concept of machine design and their types. • Factors ... approach at every stage of the design is needed. Use of factor of safety in designing the elements is to optimize the design to avoid over- design for reliability. 1.1.7 Summary...

Ngày tải lên: 17/12/2013, 11:15

... considered to be the ability of the material to absorb energy in the plastic zone. The measure of toughness is the amount of energy absorbed after being stressed upto the point of fracture. (i) Creep- ... Instructional Objectives At the end of this lesson, students should know • Properties and applications of common engineering materials. • Types and uses of ferrous m...

Ngày tải lên: 17/12/2013, 11:15

... other, the nature of fit is dependent on the limits of tolerances and fundamental deviations of the mating parts. The nature of assembly of two mating parts is defined by three types of fit system, ... or manufacture a product range. The range of operational speeds of a machine or the range of powers of a typical machine may be also as per a series of preferred num...

Ngày tải lên: 17/12/2013, 11:15

... that the state of stress at a point can be given by six stress components only. It is important to understand the implication of this state of stress at a point in the design of machine elements ... aluminium shaft of 100mm diameter by a tubular steel shaft of the same outside diameter transmitting the same torque and having the same angle of twist. Find the inner radius...

Ngày tải lên: 17/12/2013, 11:15